BICSI Installer 2 - Copper - INSTC_V8 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

You are installing a new equipment rack in a Telecommunications Room (TR). Which grounding practice aligns BEST with BICSI Installer 2 guidelines?

A. Relying on the rack's anchor bolts into the concrete floor for grounding B. Bonding the rack to the telecommunications grounding busbar with a listed bonding conductor of appropriate size C. Grounding the rack to the building's structural steel using a #8 AWG copper conductor D. Connecting the rack directly to the nearest water pipe for grounding

Discussion 0

Correct Answer: B Vote an answer

Question 2

When specifying cable routing within an Equipment Room (ER), BICSI guidelines recommend that ladder racks be mounted with adequate clearance from the top of the equipment racks. What is the TYPICAL recommended vertical clearance?

A. 15 cm (6 in) B. 60 cm (24 in) C. 45 cm (18 in) D. 30 cm (12 in)

Discussion 0

Correct Answer: D Vote an answer

Question 3

Regarding safety protocols from the BICSI Installer 2 manual, which is the MOST important initial step before using a power puller for cable installation?

A. Conducting a thorough job hazard analysis (JHA) or risk assessment B. Wearing a full-body harness, regardless of the installation height C. Ensuring the puller's label matches the cable category D. Verifying that all conduit runs are reamed and free of burrs

Discussion 0

Correct Answer: A Vote an answer

Question 4

Which of the following must be measured before the length of a coaxial cable can be calculated?

A. Delay skew B. DC loop resistance C. Insertion loss D. Propagation delay

Discussion 0

Correct Answer: B Vote an answer

Question 5

What type of coaxial cable is used for video backbone distribution?

A. RG 59 B. Series 11 C. Series 6 D. RG 58

Discussion 0

Correct Answer: B Vote an answer

Question 6

A purple backboard should be used to identify ________?

A. Demarcation point B. Network connections C. Common equipment D. Horizontal cable

Discussion 0

Correct Answer: C Vote an answer

Question 7

Which of the following testing parameters is REQUIRED for Category 6A balanced twisted-pair cabling to verify compliance with TIA standards during certification testing?

A. Temperature, Humidity, and Crosstalk Deratings B. NEXT, PSNEXT, Return Loss, Insertion Loss, PSANEXT, and PSAACR-F C. Wire Map and DC Resistance only D. Return Loss, Resistance, Capacitance, and Impedance

Discussion 0

Correct Answer: B Vote an answer

Question 8

Which of the following scenarios would MOST likely violate the code requirements related to fire-stopping as identified in BICSI Installer 2 best practices?

A. Pulling a cable bundle through an existing firestop without re-sealing around the annular space B. Using permanently intumescent sealant around cable bundles passing through a fire-rated wall C. Installing cable through a listed firestop assembly for electrical conduit D. Using a split sleeve design specifically tested for the cable type

Discussion 0

Correct Answer: A Vote an answer

Question 9

Which of the following is used to express system gain and loss?

A. Ohms B. Decibel (dB) C. Henries D. Farads

Discussion 0

Correct Answer: B Vote an answer

Question 10

What is the recommended minimum amount of aisle space between and around equipment?

A. 1 m (3.3') B. 1.2 m (4') C. 1.52 m (5') D. 0.6 m (2')

Discussion 0

Correct Answer: A Vote an answer

Question 11

Which of the following is the primary benefit of using wall-mounted racks and cabinets in place of traditional equipment racks?

A. Provides equipment with a higher level of protection B. Optimizes airflow within the equipment room C. Allows for the equipment to be easily rearranged D. Takes up less space within the equipment room

Discussion 0

Correct Answer: D Vote an answer