Juniper.JN0-647.v2019-01-23.q44

Exam Code:JN0-647
Exam Name:Enterprise Routing and Switching Exam
Certification Provider:Juniper
Free Question Number:44
Version:v2019-01-23
Rating:
# of views:223
# of Questions views:1745
Start Practice Test

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Other Version
598 viewsJuniper.JN0-647.v2018-03-06.q39
Exam Question List
Question 1: Click the Exhibit. (Exhibit) You have deployed the access co...
Question 2: Which protocol is used for port-level access control and aut...
Question 3: Which three statements are true about strict-high priority q...
Question 4: Click the Exhibit. (Exhibit) You have deployed Sparse Mode m...
Question 5: In a Layer 2 environment where 802.1X is deployed with its d...
Question 6: Click the Exhibit. (Exhibit) You are troubleshooting an OSPF...
Question 7: Click the Exhibit. (Exhibit) You are adding a Junos Fusion s...
Question 8: Click the Exhibit. (Exhibit) You have three switches, each w...
Question 9: Click the Exhibit. (Exhibit) The Receiver is attempting to j...
Question 10: Click the Exhibit. (Exhibit) Router1, in peer AS 65001, adve...
Question 11: Click the Exhibit. (Exhibit) Referring to the exhibit, traff...
Question 12: Which statement is correct about CoS policers on Junos devic...
Question 13: A new PoE+VoIP handset was added to an EX Series device. The...
Question 14: Which statement is correct about MSTP?...
Question 15: Click the Exhibit. (Exhibit) You have a workstation and VoIP...
Question 16: Click the Exhibit. (Exhibit) A customer is concerned that th...
Question 17: Click the Exhibit. (Exhibit) Your network is experiencing co...
Question 18: Click the Exhibit. (Exhibit) Referring to the exhibit, you a...
Question 19: Which protocol is a multicast routing protocol?...
Question 20: When configuring class of service, what would you use to all...
Question 21: Click the Exhibit. (Exhibit) Referring to the exhibit, which...
Question 22: Click the Exhibit. (Exhibit) You are configuring dynamic ren...
Question 23: Click the Exhibit. (Exhibit) Router R1, in peer AS 65001, ad...
Question 24: You want to implement an RP in your PIM sparse mode environm...
Question 25: Click the Exhibit. (Exhibit) You have just configured on an ...
Question 26: Click the Exhibit. (Exhibit) Referring to the exhibit, you h...
Question 27: You configured static mode power management on an EX4300 to ...
Question 28: Click the Exhibit. (Exhibit) Which AS path matches the AS pa...
Question 29: Click the Exhibit. (Exhibit) Referring to the exhibit, Area ...
Question 30: You are configuring a scheduler map on an EX9200 Series devi...
Question 31: Click the Exhibit. (Exhibit) Referring to the exhibit which ...
Question 32: Which two statements are true about 802.1Z dynamic filters b...
Question 33: Click the Exhibit. (Exhibit) Switch 4 is rebooted as shown i...
Question 34: OSFP is stuck in the ExStart state. What is a common cause o...
Question 35: Which two statements are true about OSPFv3? (Choose two.)...
Question 36: You are enabling 802.1X authentication on an EX Series devic...
Question 37: You created a firewall rule to protect the Routing Engine. A...
Question 38: Click the exhibit. (Exhibit) Where is the policy shown in th...
Question 39: What information must you gather from the satellite device t...
Question 40: Computers on the network are assigned IP addresses from DHCP...
Question 41: Click the Exhibit. (Exhibit) The ping command shows that con...
Question 42: You are asked to merge a RIP network with your OSPF network....
Question 43: Click the Exhibit. (Exhibit) You have configured 802.1X sing...
Question 44: Click the Exhibit. (Exhibit) All of the clients attached to ...