ASQ Certified Quality Inspector - CQI FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

A caliper that is typically used at the mill to accept parts was sent out for calibration. After it came back, the calibration certificate indicated that the caliper was out of spec when it was received by the calibration service. What is the next step?
Response:

A. Hold a meeting with appropriate people to find out what impact this has on the product B. Throw the caliper out C. Hold the operator responsible for using a caliper that was out of spec D. Immediately place all product on hold and scrap

Discussion 0

Correct Answer: A Vote an answer

Question 2

Bilateral tolerance refers to:
Response:

A. the total amount a specific dimension is permitted to vary. The tolerance is the difference between the maximum and minimum limits. B. a tolerance in which variation is permitted in both directions from the specified dimension. C. a tolerance in which variation is permitted in one direction from the specified dimension. D. the general term applied to the category of tolerances used to control form, profile, orientation, location, and runout.

Discussion 0

Correct Answer: B Vote an answer

Question 3

What is 118º 45' 19.4" minus 106º 51' 19.6"?
Response:

A. 12º 53' 59.8" B. 11º 53' 58.8" C. 11º 52' 57.8" D. 11º 53' 59.8"

Discussion 0

Correct Answer: D Vote an answer

Question 4

What is the total combined length of these four parts in inches expressed as a decimal 1/64 in., 2/9 in., 7/32 in., and 14/27 in?
Response:

A. 0.9711551 B. 0.9571157 C. 0.9750055 D. 0.9751157

Discussion 0

Correct Answer: D Vote an answer

Question 5

A triangle has two sides adjacent to the 90 angle that measure 6 mm and 20 mm. The length of the hypotenuse is Response:

A. 436.00 mm B. 20.88 mm C. 4.57 mm D. 26.00 mm

Discussion 0

Correct Answer: B Vote an answer

Question 6

Convert 7.85 x 105 from scientific notation to floating point notation.
Response:

A. 78.5 B. 0785 C. 0.785 D. 785 000

Discussion 0

Correct Answer: D Vote an answer

Question 7

Convert 32,000 to scientific notation.
Response:

A. 3.2 x 104 B. .324 x 105 C. 32 x 103 D. 320 x 102

Discussion 0

Correct Answer: A Vote an answer

Question 8

Advantages of digital scales versus dial and vernier scales are:
Response:

A. All of the above B. Reduced errors in reading values C. The reduction in cosine error D. A greater number of digits of display resolution

Discussion 0

Correct Answer: A Vote an answer

Question 9

How many micro inches in 2.5 inches?
Response:

A. 2,500,000 B. 25,000 C. 25,000,000 D. 2,500

Discussion 0

Correct Answer: A Vote an answer

Question 10

An inspector wishes to determine the frequency of defects that have been found during the inspection of a specific part in order to set priorities for resolution. The attribute data could best be evaluated using which of the following?
Response:

A. A histogram B. A Pareto chart C. A run chart D. A scatter diagram

Discussion 0

Correct Answer: B Vote an answer

Question 11

Plug gages and ring gauges have which of the following in common?
Response:

A. They both check outside dimensions B. They have the same accuracy C. They both check inside dimensions D. They are both attribute gauges

Discussion 0

Correct Answer: D Vote an answer

Question 12

All of the following situations indicate the need for a product audit EXCEPT when Response:

A. product is found defective after 100% inspection B. a customer identifies a product inventory discrepancy C. a new product is being released for the first time D. nonconforming product is received by a customer

Discussion 0

Correct Answer: B Vote an answer

Question 13

Team progression begins with which stage when members cautiously explore boundaries of acceptable group behavior?
Response:

A. Storming B. Forming C. Performing D. Norming

Discussion 0

Correct Answer: B Vote an answer

Question 14

The task is to measure hole to hole in a vertical pattern. The holes are set at 90 degrees to each other. Which equipment of the following is a good choice?
Response:

A. Height gauge and Indicator B. Indicator and Parallel bars C. Height gauge and V-Block D. V-Block and Parallel bars

Discussion 0

Correct Answer: A Vote an answer