CWNP Certified Wireless Design Professional - CWDP-305 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

HR/DSSS specifies the following PHY rates:
Response:

A. 1, 2 B. MCS 1-15 C. 1, 2, 5.5, 11 D. 6, 9, 12, 18, 24, 36, 48, 54

Discussion 0

Correct Answer: C Vote an answer

Question 2

You told your customer that multipath fading may be mitigated simply by moving one or both of the receivers antennas a small amount, usually by one to four wavelengths away from its original position. Your customer is prepared to make the change, but does not know the wavelength for
802.11ac.
What is the approximate wavelength of an 802.11ac radio wave?

A. 15.24 cm (6 inches) B. 12 cm (4.72 inches) C. 5.5 cm (2.16 inches) D. 45 cm (17.71 inches)

Discussion 0

Correct Answer: C Vote an answer

Question 3

What are methods of providing RF high availability?
Response:

A. Deploy using 100 percent overlap. B. Power APs to maximum power. C. Deploy 802.3af. D. Use dual spectrums. E. Use the HSRP/VRRP protocol.

Discussion 0

Correct Answer: A Vote an answer

Question 4

You are validating association capabilities from clients to an 802.1X/EAP secure SSID. The RADIUS server's IP address is 10.100.50.25 and the default RADIUS authentication port is used. When testing them, none of the clients are able to associate to the SSID. Troubleshooting the WLAN infrastructure, you found out that the server is up and the RADIUS service is up as well, but the authenticator is not able to communicate properly with the server. What's your next troubleshooting step?

A. Reboot the clients B. Verify that the shared secret between the authenticator and the RADIUS server is correct C. Reboot the server D. Restart the RADIUS service

Discussion 0

Correct Answer: B Vote an answer

Question 5

You are selecting external antennas for use in a bridge link deployment. What chart should you request from the antenna vendors to make an accurate selection?

A. dBm to dB conversion chart B. Elevation chart C. mW to dBm conversion chart D. Antenna coating chart

Discussion 0

Correct Answer: B Vote an answer

Question 6

What are the deliverables to your customer after successfully implementing a WLAN infrastructure?

A. Digital or physical assets, guides, floorplans and configuration documents B. Facility blueprints C. Nothing is required. The implemented WLAN was deliverable D. Project Charter

Discussion 0

Correct Answer: A Vote an answer

Question 7

If you choose to recommend dynamic channel assignment for the APs in your WLAN design what action should you also recommend'?

A. Ensure that the output power of an APs is set to the minimum available in the system interface B. Configure the settings used by the dynamic channel assignment algorithm optimally for your design C. Replace all antennas with panel antennas instead of omnidirectional antennas D. Ensure that the output power of all APs is set to the maximum allowed in the regulatory domain

Discussion 0

Correct Answer: B Vote an answer

Question 8

As an implementation engineer, you have just received initial design specs from a network designer for your dual-band 802.11n deployment. The network design documents prescribe the following data rate configuration for the 2.4 GHz radio:
Basic Rates 5.5, 6, 11, 12 Mbps
Supported Rates 9, 18, 24, 36, 48, and 54 Mbps as well as MCS 0-15
What will result from this design strategy?

A. HR/DSSS (802.11b) stations will not be able to associate to the service set. B. This configuration violates the IEEE specification that defines 6, 12, and 24 Mbps as mandatory data rates for 802.11g/n. C. By disabling support for 1 and 2 Mbps while allowing 5.5 and 11 Mbps, the network will force 802.11b clients to use these higher data rates. D. Protection mechanisms will always be in use on this network to support 5.5 and 11 Mbps as basic rates.

Discussion 0

Correct Answer: C Vote an answer