Cisco Certified Network Associate - 200-125 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

Refer to the exhibit.

Drag and drop the routing table components on the left onto the corresponding letter from the exhibit on the right. Not all options are used

Discussion 0

Correct Answer:

Question 2

What two actions can be taken to secure the virtual teminal interfaces on a router? (choose two)

A. Configure a virtual terminal password and logi process B. Create an access list and apply it to the virtual terminal interfaces using the access-group command C. Enter an access list and apply it to the virtual terminal interfaces using the access-class command D. Administratively shut down the interface E. Physically secure the interface

Discussion 0

Correct Answer: A,C Vote an answer

Question 3

Refer to the exhibit.

What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN? (choose two)

A. The number of collision domains would decrease. B. The number of collision domains would remain the same. C. The number of collision domains would increase. D. The number of broadcast domains would increase. E. The number of broadcast domains would remain the same.

Discussion 0

Correct Answer: C,E Vote an answer

Question 4

Assuming a subnet mask of 255.255.248.0, three of the following addresses are valid host addresses.
Which are these addresses? (Choose three.)

A. 172.16.8.0 B. 172.16.9.0 C. 172.16.20.0 D. 172.16.31.0

Discussion 0

Correct Answer: B,C,D Vote an answer

Question 5

Why has the Branch3 router lost connectivity with R1? Use only show commands to troubleshoot because usage of the debug command is restricted on the Branch3 and R1 routers.

A. A PPP chap hostname mismatch is noticed between Branch3 and R1. B. A PPP chap password mismatch is noticed between Branch3 and R1. C. The PPP chap hostname and PPP chap password commands are missing on the Branch3 router. D. PPP encapsulation is not configured on Branch3.

Discussion 0

Correct Answer: A Vote an answer

Question 6

Refer to the exhibit.

If the devices produced the given output, what is the cause of the EtherChannel problem?

A. There is a speed mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces. B. There is an encapsulation mismatch between SW1's Fa0/1 and SW2's Fa0/1 interface C. There is an MTU mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces D. SW1's Fa0/1 interface is administratively shut down.

Discussion 0

Correct Answer: A Vote an answer

Question 7

Which two statements about VTP are true? (Choose two.)

A. All switches must be configured with a unique VTP domain name B. All switches must be configured with the same VTP domain name C. The VTP server must have the highest revision number in the domain D. All switches must be configured to perform trunk negotiation. E. All switches must use the same VTP version.

Discussion 0

Correct Answer: B,C Vote an answer

Question 8

Which of the following describes the roles of devices in a WAN? (Choose three.)

A. A router is commonly considered a DTE device B. A CSU/DSU terminates an analog local loop C. A modem terminates an analog local loop D. A router is commonly considered a DCE device E. A CSU/DSU terminates a digital local loop F. A modem terminates a digital local loop

Discussion 0

Correct Answer: A,C,E Vote an answer

Question 9

Which three elements are fields in a basic Ethernet data frame? (choose three)

A. Frame Check Sequence B. Version C. Header Checksum D. Preamble E. Length/Type F. Time to Live

Discussion 0

Correct Answer: A,D,E Vote an answer

Question 10

Which two EtherChannel PAgP modes can you configure? (choose two)

A. desirable B. on C. auto D. passive E. active

Discussion 0

Correct Answer: A,C Vote an answer

Question 11

Which IPV6 feature is supported in IPV4 but is not commonly used?

A. broadcast B. anycast C. unicast D. multicast

Discussion 0

Correct Answer: B Vote an answer

Question 12

Router R6 does not form an EIGRP neighbor relationship correctly with router R1.
What is the cause for this misconfiguration?

A. The passive-interface command is enabled. B. The K values mismatch. C. The network command is missing. D. The AS does not match.

Discussion 0

Correct Answer: B Vote an answer

Question 13

Which set of commands is recommended to prevent the use of a hub in the access layer?

A. switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1 B. switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security mac-address 1 C. switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1 D. switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1

Discussion 0

Correct Answer: A Vote an answer

Question 14

Which command can you enter to determine whether serial interface 0/2/0 has been configured using HDLC encapsulation?

A. router#show ip interface brief B. router#show ip interface s0/2/0 C. router#show platform D. router#show interfaces Serial 0/2/0

Discussion 0

Correct Answer: D Vote an answer