Cisco Implementing Cisco IP Telephony & Video, Part 1 (CIPTV1) - 300-070 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

Which three types of devices can you test with the Cisco Unified Communications Manager Dialed Number Analyzer tool? (Choose three)

A. Cisco Catalyst Switches. B. Fax/Modem. C. Trunks. D. Cisco ASA Adaptive Security Appliances. E. Gateways. F. Phones.

Discussion 0

Correct Answer: C,E,F Vote an answer

Question 2

When dialing 1234, which rule is matched first?

A. translation pattern 12[123]X B. directory number 12345 C. route pattern 12[123]X D. route pattern 1XXX E. translation pattern 1XXX

Discussion 0

Correct Answer: A Vote an answer

Question 3

What is the purpose of using device pools?

A. to provide all the IP phone parameters required for auto-registration B. to provide an easily modified set of system parameters for the Cisco Unified CallManager server and endpoints C. to provide a convenient way to define a set of common characteristics that can be assigned to devices D. to consolidate the dial plan for a set of IP phones in the same location

Discussion 0

Correct Answer: C Vote an answer

Question 4

Which statement is true?

A. VolP dial peers use the H 323 signaling protocol by default. B. VolP dial peers use the MGCP signaling protocol by default. C. VolP dial peers are POTS by default. D. VolP dial peers use the SIP signaling protocol by default.

Discussion 0

Correct Answer: A Vote an answer

Question 5

Which three commands show the output of an active video call? (Choose three.)

A. show voice call B. show vrm active_calls C. show voip rtp connections D. show call active video brief E. show voice call summary F. show video dsp

Discussion 0

Correct Answer: C,D,E Vote an answer

Question 6

Which mechanism is often configured on the edges of a network to control the maximum rate of traffic that is sent or received on an interface and to classify the traffic into priority levels or class of service?

A. access control B. traffic regulation C. routing D. shaping E. policing

Discussion 0

Correct Answer: E Vote an answer

Question 7

If no SIP dial rules are configured on an IP phone, at which three points in the collection of digits does a Type A SIP phone send digits to the Cisco Unified Communications Manager? (Choose three.)

A. when the user presses the # key B. when the collected digits match a SIP dial rule C. when the interdigit timer expires D. when the user presses the Dial softkey E. as each digit is collected (it is sent for analysis)

Discussion 0

Correct Answer: A,C,D Vote an answer

Question 8

Refer to the exhibit. Which option is the most highly recommended option to install Cisco TelePresence Conductor on the virtual machine?

A. Thick Provision Lazy Zeroed B. Thick Provision C. Thin Provision D. Thick Provision Eager Zeroed

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 9

Refer to the exhibit and configuration output. What are the two main ways from New York to call Extension 6001 in England? (Choose two.)

sh run | s Dial-peer
dial-peer voice 2 voip
destination-pattern 6...
preference 0
session-target ipv4: 200.10.10.5
dtmf-relay sip-notify dial-peer voice 3 pots
destination-pattern 6...
preference 1
port 0/0/0:23
prefix 757385
dtmf-relay sip-notify

A. The second way is PSTN. B. The first way is WAN. C. The first way is PSTN. D. The second way is WAN.

Discussion 0

Correct Answer: A,B Vote an answer

Question 10

What are the two steps to configure NTP on a Cisco Unified Communications Manager publisher to support SCCP phones? (Choose two.)

A. Restart the Unified Communications Manager services for the publisher and subscribers on the Unified CallManager Serviceability page. B. Configure Phone NTP References in Cisco Unified CM Administration. C. Configure time in Cisco Unified OS Administration. D. Configure the NTP server in Cisco Unified OS Administration. E. Configure the NTP server in Cisco Unified CM Administration.

Discussion 0

Correct Answer: A,D Vote an answer

Question 11

Which device uses an MIP to insert itself into and force media through a call flow?

A. SCCP B. conference resource C. OTRP D. H.323 gateway

Discussion 0

Correct Answer: C Vote an answer

Question 12

Which distribution algorithm is used for a route group?

A. Top down, broadcast, circular. B. Circular, top down. C. Longest idle, broadcast. D. Circular, top down, longest idle, broadcast.

Discussion 0

Correct Answer: B Vote an answer

Question 13

Which option describes destinations that can be routed?

A. DNs located in the partitions inside its calling search space B. DNs on the allowed list in the ACL of the registered Cisco Unified Communications Manager server C. DNs not listed on the restricted dialing list of the device D. DNs on the trusted list of the CA within the Cisco Unified Communications Manager cluster

Discussion 0

Correct Answer: A Vote an answer

Question 14

How does Cisco Unified Cisco Unified Communications Manager perform digit analysis?

A. Send all collected digits through the Dialed Number Analyzer to determine the best call routing match within Cisco Unified CM B. Perform a digit-by-digit analysis to find the best matching route pattern within the partition list in the calling search space of a device C. Perform a digit-by-digit analysis to find the best matching route pattern based on a devices partition D. Use a set of route lists and filters to match all collected digits of a dialed number.

Discussion 0

Correct Answer: B Vote an answer

Question 15

Which two Cisco multiparty bridges are supported when you set up WebEx-enabled Cisco TelePresence? (Choose two)

A. Cisco TelePresence MCU B. Cisco TelePresence Server C. Cisco Unified Communications Manager SME D. Cisco lOS gateways E. Cisco Unified Border Element

Discussion 0

Correct Answer: A,B Vote an answer