Instant Access Cisco 300-110 Exam Premium Dumps - FreeCram

Walking into the 300-110 exam cold is a risk you do not have to take. In 2026, FreeCram test engines recreate the timed pressure of the Cisco Designing Cisco Wireless Networks exam, so the format feels familiar long before exam day.

Cisco 300-110 Exam Overview:

Cisco 300-110 Exam Syllabus Topics:

Cisco 300-110 Exam: Frequently Asked Questions

Cisco Designing Cisco Wireless Networks Sample Questions:

Question 1

An educational organization recently deployed an anchored WLAN and has a high number of client connections at any given time that stream video. The wireless infrastructure includes two Cisco 9800 WLCs. To prevent web traffic being slow, an engineer must configure the deployment to prevent excessive fragmentation of the client data. Which configuration must the engineer apply?

A. Set the MTU on both controllers to match.
B. Increase the MTU on both controllers.
C. Set the do not fragment bit on the mobility tunnel.
D. Adjust the TCP MSS value below the fragmentation point.

Question 2

An engineer must configure the virtual IP address on multiple controllers in a mobility group.
Which rule must the engineer follow to ensure proper roaming?

A. Use a unique IP address for each WLC.
B. Ensure that the DNS Host Name field is defined.
C. Use the same IP address for each WLC.
D. Ensure that the DNS entry is tied to the virtual IP address of the WLC.

Question 3

Refer to the exhibit. A network engineer is designing a high availability SSO on a Cisco Catalyst
9800- 40 WLC with multi-LAG network redundancy on two Catalyst 9300 switches. The LAG requirements are: ?Each LAG must be connected to a single switch. ?Different VLANs must be assigned to different LAGs. ?The controller must learn the identity of partners that can support LAG capabilities in each port. ?When any active LAG ports fail, a standby LAG port must provide redundancy. Which protocol must be used for the port channel on the interface to meet the design requirements?

A. BGP
B. OSPF
C. LACP
D. PAgP

Question 4

A consultant must design a WLAN for a large campus with high AP density, 50-100 clients per cell, 5 Mbps throughput per client minimum, 5 GHz and 2.4 GHz coverage at -67 dBm, and no
802.11b clients. Which two WLAN design approaches meet the requirements? (Choose two.)

A. Set the minimum mandatory data rates to 12-18 Mbps.
B. Configure up to six SSIDs on any AP.
C. Enable 802.11b data rates.
D. Reduce the 2.4 GHz coverage with FRA.
E. Set the 5 GHz channel widths to 80-160 MHz.

Question 5

A university has three campus locations and the main data center. Each campus location has a Cisco Catalyst 9800-40 WLC that manages 600 APs. The data center has a Catalyst 9800-40 WLC, which serves as N+1 backup for each campus WLC. A consulting engineer must install four additional Catalyst 9800-40 WLCs to serve as high availability SSO pairs for each campus, but only two have been approved due to budget restrictions. Requirements: Data center WLC must always be available as N+1 backup, Campus1 WLC must operate with zero downtime, and in the event of multiple campus outages, the AP priority order is to support Campus3, Campus2, then Campus1. Which design approach must the consulting engineer take?

A. The data center WLC and Campus3 WLC are the high availability SSO pair. Campus1 APs have priority 4, Campus2 APs have priority 2, and Campus3 APs have priority 1.
B. The data center WLC and Campus1 WLC are the high availability SSO pair. Campus1 APs have priority 4, Campus2 APs have priority 2, and Campus3 APs have priority 1.
C. The data center WLC and Campus1 WLC are the high availability SSO pair. Campus3 APs have priority 4, Campus2 APs have priority 2, and Campus1 APs have priority 1.
D. The data center WLC and Campus3 WLC are the high availability SSO pair. Campus3 APs have priority 4, Campus2 APs have priority 2, and Campus1 APs have priority 1.

Solutions: