Cisco Troubleshooting and Maintaining Cisco IP Networks (TSHOOT) - 300-135 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

Scenario:
A customer network engineer has edited their OSPF network configuration and now your customer is experiencing network issues. They have contacted you to resolve the issues and return the network to full functionality.

The 6.6.0.0 subnets are not reachable from R4. how should the problem be resolved?

A. Edit access-list 46 in R6 to permit all the 6.6.0.0 subnets B. Remove distribute-list 64 out on R6 C. Apply access-list 46 in R6 to a different interface D. Apply access-list 1 as a distribute-list out under router ospf 100 in R4 E. Remove distribute-list 1 in ethernet 0/0 in R4 F. Remove distribute-list 1 in ethernet 0/1 in R4

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 2

What is the solution of the fault condition?

A. Delete the current BGP process and reenter all of the commands using 65002 as the AS number. B. Under the BGP process, bgp confederation identifier 65001 command C. Under the BGP process, delete the neighbor 209.56.200.226 remote-as 65002 command enter the neighbor 209.65.200.226 remote-as 65002 command. D. add permit ip 209.65.200.224 0.0.0.3 any command to R1s ACL

Discussion 0

Correct Answer: D Vote an answer

Question 3

Which of the following are not true OSPF LSA rules?

A. OSPF LSA type 5 triggers an LSA type 7 at an ABR between an NSSA and the backbone area. B. OSPF LSA type 7 triggers an LSA type 5 at an ABR between an NSSA and the backbone area. C. OSPF LSA type 3 triggers an LSA type 4 at an ABR. D. OSFP LSA type 2 triggers an LSA type 3 at an ABR. E. OSPF LSA type 5 triggers an LSA type 7 at an A5BR but only in N5SAs. F. OSPF LSA type 1 triggers an LSA type 3 at an ABR.

Discussion 0

Correct Answer: A,C,E Vote an answer

Question 4

Refer to the exhibit.

The administrator has successfully logged into R1 but is unable to access privileged mode commands Which configuration is causing the problem?

A. Enable secret or enable password must be configured B. The aaa authorization reverse-access command is missing. C. The username command uses password, not secret D. The password on the VTY lines does not match the username password.

Discussion 0

Correct Answer: A Vote an answer

Question 5

Refer to the exhibit.

Client A cannot reach client B while other users from other spoke routers can reach Client B.
Which command provides the output necessary to troubleshoot the issue?

A. show ip route B. show ip interface brief C. show ip bgp sum D. show dmvpn

Discussion 0

Correct Answer: D Vote an answer

Question 6

On which plane of operation can you access and configure a router or switch?

A. management B. control C. data D. forwarding

Discussion 0

Correct Answer: A Vote an answer

Question 7

What is the solution of the fault condition?

A. Under the OSPF process, delete the redistribute eigrp 10 subnets router-map EIGRP_>OSFP command enter the redistribute eigrp 10 route-map OSPF_>EIGRP command. B. Under the OSPF process, delete the redistribute eigrp 10 subnets router-map EIGRP_>OSFPcommand enter the redistribute eigrp 10 subnets route-map EIGRP_>OSPF metric
20 command. C. Under the EIGRP process, delete the redistribute ospf 1 router-map OSPF_to_EIGRP command enter the redistribute ospf 6 route-map OSPF_to_EIGRP command. D. Under the EIGRP process, delete the command redistribute ospf 1 route-map OSPF->EIGRP enter theredistribute ospf 1 router-map OSPF_to_EIGRP command E. Under the EIGRP process, delete the redistribute ospf 1 router-map OSPF_to_EIGRPcommand enter the redistribute ospf 1 metric 100000 100 100 1 1500 route-map OSPF_to_EIGRP command.

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 8

The implementation group has been using the test bed to do an IPv6 'proof-of-concept1. After several changes to the network addressing and routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2 (2026::102:1).
Use the supported commands to isolate the cause of this fault and answer the following question.
What is the solution to the fault condition?

A. Under the interface Tunnel34 configuration delete the tunnel mode ipv6 command. B. Under the interface Serial0/0/0.34 configuration enter the ipv6 address 2026::34:1/122 command. C. Under the interface Tunnel34 configuration enter the ip address unnumbered Serial0/0/0.34 command. D. Under the interface Tunnel34 configuration delete the tunnel source Serial0/0/0.34 command and enter the tunnel source 2026::34:1/122 command.

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 9

Which of the following topology situations would be a qood candidate for configuring DMVPN?

A. Central-site VPN topology B. Remote-access VPN topology C. Full mesh VPN topology D. Managed overlay VPN topology E. Hub-and-spoke VPN topology F. Extranet VPN

Discussion 0

Correct Answer: C Vote an answer