Cisco Implementing Cisco Data Center Infrastructure - 300-165 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

Which two options accurately describe the implementation of Fibre Channel domain IDs? (Choose two.)

A. are assigned on a per-line card basis B. must be the same on all of the Fibre Channel switches in the fabric C. must be unique on all of the Fibre Channel switches in the fabric D. are assigned on a per-VSAN basis E. are assigned on a per switch basis

Discussion 0

Correct Answer: C,E Vote an answer

Question 2

Refer to the exhibit.

Which result does the configuration show?

A. border spine B. SVI configuration C. border leaf D. tenant interface

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 3

Refer to the exhibit.

Which statement about the LACP configuration is true?

A. LACP only supports Fast Ethernet links B. LACP control packets are sent 3t a rate of 1 per 10 minutes C. LACP control packets are sent at a rate of 1 per second. D. Stateful switchover is supported

Discussion 0

Correct Answer: C Vote an answer

Question 4

Which Cisco NX-OS feature allows transparent Layer 2 extension between sites?

A. OTV B. ETV C. vPC D. LISP E. FabricPath F. TrustSec

Discussion 0

Correct Answer: A Vote an answer

Question 5

Refer to the exhibit.

What is the result when you run the force command?

A. The command forces the addition of a port to a SAN port channel. B. The command forces the deletion of a port to a SAN port channel. C. The port is enabled and active. D. Port channel mode uses force mode

Discussion 0

Correct Answer: A Vote an answer

Question 6

Which task must be done before a zone set takes effect?

A. Enter the zoneset activate name <zone-name> vsan <vsan-#> command. B. Add a member to the zone. C. Enter the exit config t command. D. Enter the copy running-config startup-config command.

Discussion 0

Correct Answer: A Vote an answer

Question 7

Which item represents the process that allows FCoE multihop using T11 standard FC-BB-5?

A. N Port proxy B. distributed FCF C. FIP snooping D. FIP proxy

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 8

Which two PIM modes on a Cisco Nexus 7000 Series switch require you to configure an RP? (Choose two)

A. BIDIR B. SSM C. ASM D. SDM E. DM

Discussion 0

Correct Answer: A,C Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 9

In the dynamic vNIC creation wizard, why are choices for Protection important?

A. They allow reserve vNICs to be allocated out of the spares pool. B. They allow dynamic vNICs to be reserved for fabric failover. C. They select the primary fabric association for dynamic vNICs. D. They enable hardware-based failover.

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 10

FabricPath switch-id is 25 and load-balance is configured for L3/L4 and rotate amount is 14 byte. What information is true about FabricPath switch-id?

A. You do not have to manually assign a switch ID unless you are running a virtual port channel plus (vPC+) because the system assigns a switch ID for you when you enable FabricPath B. FabricPath topology requires manual configuration of switch-id which has a range from 1 to 4099 C. FabricPath topology requires manual configuration of switch-id which has a range from 1 to 4095 D. Every FabricPath must have a manually configured switch-id for it to form a FabricPath topology

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 11

Refer to the exhibit.

The configuration belongs to which link?

A. Link C on Switch4 B. Link D on Switch4 C. Link A on Switch2 D. Link B on Switch2

Discussion 0

Correct Answer: B Vote an answer

Question 12

Which feature does the spanning-tree port type network command enable?

A. Bridge Assurance B. BPDU Guard C. Rapid PVST+ D. TrustSec

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 13

Refer to the exhibit.

Which actions does the switch take when a security violation occurs on Ethernet 2/1?

A. Drops all the packets and then increments the security violation count. B. Places the port in an error disabled state. C. Drops all the packets without incrementing the security violation count. D. Shuts down the port.

Discussion 0

Correct Answer: A Vote an answer

Question 14

Which GLBL load-balancing method ensures that a client is always mapped to the same virtual MAC address?

A. shortest-path and weighting B. host-dependent C. vmac-weighted D. dedicated-vmac-mode

Discussion 0

Correct Answer: B Vote an answer

Question 15

Which parameter is configurable when setting up logging on the Connectivity Management Processor?

A. the directory to save the log file to B. the number of times the log can roll over C. the number of CMP messages to save in a single log file D. the severity threshold of the messages to log

Discussion 0

Correct Answer: D Vote an answer