Cisco CCIE Data Center Written - 350-080 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

In the Cisco FabricPath domain, one switch becomes the root for the multidestination tree. Cisco FabricPath switches compares which three parameters to select the root? (Choose three.)

A. Root priority B. Port ID C. Switch ID D. Subswitch ID E. Bridge ID F. System ID

Discussion 0

Correct Answer: A,C,F Vote an answer

Question 2

On a Cisco Nexus 7000 device, on which port type can port security be configured?

A. trunk ports B. SPAN destination port C. Access ports D. public VLAN-enabled ports

Discussion 0

Correct Answer: C Vote an answer

Question 3

KAL-AP on the Cisco ACE allows communication with Cisco ACE Global Site Selector, to report virtual IP and real server availability. Which statement is true about KAL-AP?

A. It is a Cisco propriety keepalive. B. It supports a maximum of 256 KAL-AP entries. C. It supports a maximum of 256 KAL-AP keepalives. D. It is used for both Cisco and non-cisco load balancers

Discussion 0

Correct Answer: A Vote an answer

Question 4

Which is true when describing a connection replication in Cisco ACE?

A. It can only be configured manually. B. It has a maximum limit of 50,000 replicated connections. C. It is not supported for SSL connections. D. It is not supported for non-SSL connections.

Discussion 0

Correct Answer: C Vote an answer

Question 5

You have configured a Cisco UCS C460 M2 Rack-Mount Server with two VIC 1225 adapters for single-wire management with Cisco UCS Manager. Which statement correctly describes the operation of these adapters?

A. One VIC will carry management, and both VICs will carry data traffic. B. The Cisco UCS C460 M2 does not support two VIC 1225 adapters simultaneously. C. Both VICs will be used for management and data traffic. D. One VIC is designated to carry management, and the other VIC is designated to carry data traffic.

Discussion 0

Correct Answer: A Vote an answer

Question 6

Refer to the exhibit.

Which statement about the interface that is connected to the NPV core switch is true?

A. The interface that is connected to the NPV switch will need to be configured as an N-Port. B. The switch that connects to the hosts is identified in the design as an NPV edge switch, and the port that connects to the core is an NP port. C. The interface that is connected to the NPV core will become an FP port. D. The link between the NPV core switch and edge will come up as an E port.

Discussion 0

Correct Answer: B Vote an answer

Question 7

What is the default vPC peer-keepalive timeout on the Cisco Nexus 7000 Series switch?

A. 500 milliseconds B. 256 milliseconds C. 1 second D. 5 seconds

Discussion 0

Correct Answer: C Vote an answer

Question 8

Refer to the exhibit.

Which two statements about the output and diagram are true? (Choose two.)

A. FI-A is configured in FC switch mode. B. The native VSAN should be VSAN 1. C. Cisco UCS will allow all VSANs by default when FC trunking is enabled. D. VSAN trunking is enabled on FI-A. E. FI-A requires VSAN pruning. F. Interface fc1/8 on MDS-A should be configured as a TE Port.

Discussion 0

Correct Answer: C,D Vote an answer

Question 9

Refer to the exhibit.

Which two options describe information that can be determined from this output? (Choose two.)

A. The default CoS configuration is being used. B. Jumbo frames have been configured on the best-effort class. C. Interface eth1/5 is configured as an uplink. D. Packets are being dropped on the interface. E. PFC is disabled on the system.

Discussion 0

Correct Answer: A,B Vote an answer

Question 10

What is the appliance port used to connect to in a Cisco Unified Computing System?

A. Fibre Channel storage B. Other fabric interconnect C. UCS chassis D. NFS storage E. UCS C-Series servers

Discussion 0

Correct Answer: D Vote an answer

Question 11

Given the following output:
San-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24:0c:00:0d: ec :d3 :5c:00 Admin port mode is NP, trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member [1]: fc2/3 Member [2]: fc2/4
What does "Speed is 8 Gbps" indicate?

A. The speed of the slowest interface in the port channel B. The combined speed of all interfaces in the port channel that are up C. The combined speed of all interfaces configured in the port channel D. The speed that can be achieved if all buffers are used

Discussion 0

Correct Answer: B Vote an answer