Cisco Troubleshooting Cisco Data Center Unified Computing - 642-035 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

A customer is configuring an upstream disjoint Layer 2 network in a Cisco UCS domain. So far they have configured the following:
Fabric Interconnects are in switching mode.
There is symmetrical configuration for high availability.
There are no overlapping VLANs.
Each vNIC is communicating with one disjoint Layer 2 network.
After validating the above, the customer is still having issues with network connectivity. What is the issue?

A. The fabric interconnect must be in end-host mode for a disjoint Layer 2 network. B. Overlapping VLANs are allowed in a disjoint Layer 2 network. C. The vNIC configuration is incorrect and must communicate with two or more disjoint layer 2 networks. D. Asymmetrical configuration for high availability needs to be configured.

Discussion 0

Correct Answer: A Vote an answer

Question 2

During a password recovery of a Cisco UCS system in a cluster configuration, what happens to blade traffic?

A. Traffic will continue to flow, but at a limited rate until the process is complete. B. There is no interruption to traffic, as the fabrics go down one at a time. C. Traffic stops flowing until the process is complete. D. There is no interruption to traffic because both fabrics stay up the whole time.

Discussion 0

Correct Answer: C Vote an answer

Question 3

Which is the cause of the disk being unavailable, during the installation of ESXi on a C-Series UCS server the logical 4TB disk for the installation client?

A. The logical drive was created using the Embedded Software Raid Controller B. VMware requires the LSI Drivers to be installed first C. The logical drive is in RAID0 D. The logical drive is not available as RAID has not completed building

Discussion 0

Correct Answer: A Vote an answer

Question 4

Which two types of ports are MAC addresses when operating in switch mode? (Choose two.)

A. backplane B. server C. uplink D. FEX

Discussion 0

Correct Answer: B,C Vote an answer

Question 5

What is the maximum number of boot targets for an FCoE vHBA on a Cisco UCS C-Series server?

A. 3 B. 2 C. 1 D. 4

Discussion 0

Correct Answer: D Vote an answer

Question 6

Which option causes an operating system on a UCS device to consistently crash several minutes after booting?

A. incorrect boot order B. out-of-date network adapter firmware C. disabled trusted platform module D. faulty power supply E. incompatible operating system driver

Discussion 0

Correct Answer: E Vote an answer

Question 7

HOTSPOT

Discussion 0

Correct Answer:

Question 8

Which Cisco UCS C Series command sequence initiates the sending of a technical support file to a TFTP server?

A. ucs /cimc # scope system-support ucs /cimc/system-support # set tftp-ip 10.1.1.1 ucs /cimc/system-support *# set path \showtechsupport ucs /cimc/system-support *#commit ucs /cimc/system-support *#start B. ucs /cimc # scope support ucs /cimc/support # set tftp-ip 10.1.1.1 ucs /cimc/support *# set path \showtechsupport ucs /cimc/support *#commit ucs /cimc/support *#start C. ucs /cimc # scope tech-support ucs /cimc/tech-support # set tftp-ip 10.1.1.1 ucs /cimc/tech-support *# set path \showtechsupport ucs /cimc/tech-support *#commit ucs /cimc/tech-support *#start D. ucs /cimc # scope tech-support ucs /cimc/tech-support # set ip 10.1.1.1 ucs /cimc/techsupport *# set tftp-path \showtechsupport ucs /cimc/tech-support *#commit ucs /cimc/techsupport *#start

Discussion 0

Correct Answer: C Vote an answer

Question 9

What is the reason that no C-Series servers can access Fibre Channel storage from this Cisco Nexus 554SUP switch?

A. VSAN mis-match on Fibre Channel interfaces B. None of the virtual fibre channel interfaces are configured C. Zoning mode mis-match with the MDS 9124 D. There are no active Fibre Channel interfaces

Discussion 0

Correct Answer: A Vote an answer