Cisco Conducting Cisco Unified Wireless Site Survey (CUWSS) v2.0 - 642-732 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

A site survey proposes placement of new APs to replace older APs. Which three options are three potential placements of the new APs? (Choose three.)

A. Deploy APs every 3000 square feet. B. Mount new APs on the exact location according to site survey report. C. Use network cables and mounting brackets from the older installation. D. Add APs from the site survey that have no APs in older installation. E. Deploy APs every 4000 square feet. F. Use the old placements where they are near the proposed location.

Discussion 0

Correct Answer: B,D,F Vote an answer

Question 2

An outdoor mesh network is being designed with one RAP and then a single RF hop to MAP1 and another single RF hop from MAP1 to MAP2 to extend coverage. Given that the initial RF backhaul at the RAP is operating at 24 Mb/s, what is the expected RF backhaul bandwidth at MAP2?

A. 20 Mb/s B. 1 Mb/s C. 7 Mb/s D. 14 Mb/s E. 3 Mb/s F. 24 Mb/s

Discussion 0

Correct Answer: D Vote an answer

Question 3

DRAG DROP

Discussion 0

Correct Answer:

Question 4

You have a multinational customer that would like you to perform a wireless site survey for a new manufacturing facility in Singapore. They have had a local vendor install a point-topoint wireless bridge link between two buildings 1 km apart. The ground between the buildings is flat but because facilities are in the mountains, dense fog is an issue. There are no line of sight issues between the buildings. The link is experiencing errors and throughput issues. Currently the two radios are set to operate at 2.4 GHz and the transmit power is set to 7 dBm with 7 dBm antennas. What do you need to take into consideration when performing the site survey for this link?

A. Change the radio power to 20 dBm and replace with a 16 dBm antenna. B. Change the radio power to 17 dBm. C. Change the radio power to 29 dBm. D. Change the radio power to 13 dBm.

Discussion 0

Correct Answer: D Vote an answer

Question 5

What is the attenuation of a wireless signal that passes through a cider block wall?

A. 12 dB B. 4 dB C. 6 dB D. 3 dB

Discussion 0

Correct Answer: B Vote an answer

Question 6

You have a customer that is building a new campus of four 3-story buildings that you have just completed the site survey for. The customer is interested in the amount of rack space they will need to allocate in either the building MDF or in the data center for controllers. Each building is going to require 75 APs to support voice and data. How should the controllers be deployed to provide the least number of controllers, the highest redundancy, and the easiest management?

A. Use the centralized deployment method in the data center with the N + N redundancy method. B. Use the distributed deployment method in each building MDF with the N + N +1 redundancy method. C. Use the centralized deployment method in the data center with the N + N + 1 redundancy method. D. Use the distributed deployment method in each building MDF with the N + N redundancy method. E. Use the centralized deployment method in the data center with the N + 1 redundancy method. F. Use the distributed deployment method in each building MDF with the N + 1 redundancy method.

Discussion 0

Correct Answer: C Vote an answer

Question 7

DRAG DROP

Discussion 0

Correct Answer:

Question 8

Which two of the following are considered best practices upon the completion of a wireless installation? (Choose two.)

A. Test all the customer's wireless devices and applications to ensure they are working properly. B. Spend time with the customer showing them the controller GUI as well as inform them how they can reach the Cisco TAC if they have any problems. C. Make sure the customer is aware that they should consider purchasing a support contract immediately after the installation is complete. D. Consult with the customer to ensure that the IT staff has a complete set of design and installation documents.

Discussion 0

Correct Answer: A,D Vote an answer

Question 9

Given an AP that can transmit at 100 mW and the client at 40 mW, which power setting should be used for a site survey?

A. 80 mW B. 10 mW C. 20 mW D. 40 mW E. 100 mW F. 60 mW

Discussion 0

Correct Answer: C Vote an answer