EMC Dell PowerSwitch Data Center Deploy 2023 - D-PDC-DY-23 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

Which two commands display if a port is currently active in a VLAN?

A. "show startup-configuration" and "show vlan" B. "show interface vlan" and "show interfaces status" C. "show vlan" and "show interfaces status" D. "show interface vlan" and "show startup-configuration"

Discussion 0

Correct Answer: C Vote an answer

Question 2

Which field in an IP header is used for QoS marking?

A. ToS B. CoS C. Options Header

Discussion 0

Correct Answer: A Vote an answer

Question 3

Which command can be used to enable SSH access to an OS10 switch?

A. ip mgmt ssh enable B. no ip telnet disable C. ip ssh server enable D. no ip ssh server disable

Discussion 0

Correct Answer: C Vote an answer

Question 4

Which is a default behavior for VLT VRRP?

A. authentication B. no preempt C. vrrp version 3 D. active-active

Discussion 0

Correct Answer: D Vote an answer

Question 5

Which two spanning-tree methods are supported by VLT on a Dell Z9284F-ON? (Select 2)

A. MSTP B. STP C. RSTP D. RSTP-PV

Discussion 0

Correct Answer: A,C Vote an answer

Question 6

What is the security impact of enabling LLDP?

A. Login over telnet is permitted. B. Broadcasts toms are possible. C. Switch information is advertised. D. SNMP data is broadcasted on all ports

Discussion 0

Correct Answer: C Vote an answer

Question 7

When implementing the VRRP tracking feature, what is the default priority exist of a tracked interface?

A. 100 B. 10 C. 1 D. 254

Discussion 0

Correct Answer: B Vote an answer

Question 8

A network administrator wants to configure a timing protocol with these requirements:
- Hardware time stamping to achieve sub microsecond synchronization.
- Master IP address: 192.168.1.100.
- Use interface Ethernet 1/1/1 to enable timing protocol.
Which configuration supports the requirements?

A. OS10(config)# ntp authenticate
OS10(config)# ntp trusted-key 345
OS10(co345 md5 0 5A60910FED211F02
OS10(config)# ntp server 192.168.1.100 key 345
OS10(config-if-eth1/1/1)# nfig)# ntp authentication-key ntp master 7 B. OS10(config)# ptp clock boundary
OS10(config)# ptp domain 1
OS10(config)# ptp system time enable
OS10(config-if-eth1/1/1)# ptp enable
OS10(config-if-eth1/1/1)# ptp role slave
OS10(config-if-eth1/1/1)# ptp transport ipv4 unicast slave
OS10(config-if-eth1/1/1-ptp-ipv4-slave)# master 192.168.1.100 C. OS10(config-if-eth1/1/1)# ntp authenticate
OS10(config-if-eth1/1/1)# ntp trusted-key 345
OS10(config-if-eth1/1/1)# ntp authentication-key 345 md5 0 5A60910FED211F02 OS10(config-if-eth1/1/1)# ntp server 192.168.1.100 key 345 OS10(config-if-eth1/1/1)# ntp master 7 D. OS10(config)# ptp clock boundary
OS10(config)# ptp domain 1
OS10(config)# ptp system time enable
OS10(config)# ptp enable
OS10(config)# ptp role master
OS10(config)# ptp transport ipv4 unicast slave
OS10(config-if-eth1/1/1)# master 192.168.1.100

Discussion 0

Correct Answer: B Vote an answer

Question 9

What is required to enable ECMP in BGP?

A. OSPF must install equal cost paths in the routing table for BGP use ECMP. B. Maximum-paths and multipath-relax commands. C. ECMP is not possible in BGP. D. Sub-interfaces must be configured on the physical interface running BGP.

Discussion 0

Correct Answer: B Vote an answer