EMC Dell PowerMax and VMAX Family Solutions Operate 2023 - D-PVM-OE-23 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

What is the correct sequence in the basic database backup workflow for a PowerMax array with a ProtectPoint solution?

A. 1. Data Domain creates and stores a backup image of the snapshot
2. Application administrator sets the database in Hot Backup mode on the application host
3. Source array analyzes the data and copies the changed data to an encapsulated Data Domain device
4. ProtectPoint creates a snapshot of the primary storage device on the source array B. 1. Application administrator sets the database in Hot Backup mode on the application host
2. ProtectPoint creates a snapshot of the primary storage device on the source array
3. Data Domain creates and stores a backup image of the snapshot
4. Source array analyzes the data and copies the changed data to an encapsulated Data Domain device C. 1. Data Domain creates and stores a backup image of the snapshot
2. Source array analyzes the data and copies the changed data to an encapsulated Data Domain device
3. ProtectPoint creates a snapshot of the primary storage device on the source array
4. Application administrator sets the database in Hot Backup mode on the application host D. 1. ProtectPoint creates a snapshot of the primary storage device on the source array
2. Application administrator sets the database in Hot Backup mode on the application host
3. Data Domain creates and stores a backup image of the snapshot
4. Source array analyzes the data and copies the changed data to an encapsulated Data Domain device

Discussion 0

Correct Answer: C Vote an answer

Question 2

You are attempting to install Unisphere for VMAX 8.0 on a server with the following configuration:
- Microsoft Windows Server 2008 32-bit
- Dual core processor
- 16 GB RAM
- 180 GB free space
The installation is unable to continue because a pre-requisite has not been met.
What is the likely cause of the error?

A. 24 GB of RAM is required. B. 240 GB of free space is required. C. Quad core processor is required. D. 64-bit operating system is required.

Discussion 0

Correct Answer: D Vote an answer

Question 3

Which Unisphere for VMAX Storage Resource Pool (SRP) view shows the Disk Groups that comprise the SRP?

A. Compliance Report B. SRP Details C. SRP Demand Report D. Workloads Demand Report

Discussion 0

Correct Answer: B Vote an answer

Question 4

What happens when the SRP reaches the Reserved Capacity limit?

A. Array increases compression priority B. No additional snapshots can be created C. All devices become read only D. No additional devices can be created

Discussion 0

Correct Answer: B Vote an answer

Question 5

Which tool must be used to verify capacity calculations and cache requirements before enabling compression on a VMAX All Flash array?

A. Unisphere for VMAX B. FAST Array Advisor C. VMAX Sizer D. Workload Planner

Discussion 0

Correct Answer: C Vote an answer

Question 6

What is the size of a VMAX3 Gatekeeper device?

A. 6 Cyl B. 3 MB C. 6 MB D. 3 GB

Discussion 0

Correct Answer: C Vote an answer

Question 7

After executing a cancel -revert operation on a Non-Disruptive Migration session, what will be the state of the I/O paths from the host to the target VMAX3 array?

A. Balanced B. Standby C. Active D. Dead

Discussion 0

Correct Answer: D Vote an answer

Question 8

Where is the service level applied?

A. LUN B. Masking View C. Storage Group D. Initiator Group

Discussion 0

Correct Answer: C Vote an answer

Question 9

If a Gatekeeper is listed in both the gkselect and the gkavoid files, what will happen during the selection of Gatekeepers?

A. Neither entry is used B. gkselect entry is used C. Either entry could be used D. gkavoid entry is used

Discussion 0

Correct Answer: A Vote an answer

Question 10

A host is connected to two PowerMax arrays with SRDF/Metro Host l/Os cannot be delivered across the SRDF link. The devices in the SRDF group have been forced into a Not Ready state to the host.
Which attribute is set on the SRDF group to cause this behavior?

A. Update After Resume Link B. Local Auto Link Recovery C. Limbo Period D. Local Link Domino

Discussion 0

Correct Answer: A Vote an answer

Question 11

Where is the automatic backup feature for the Solutions Enabler Group Name Services (GNS) database set?

A. Daemon options file B. Unisphere for VMAX C. Installation wizard D. SYMAPI options file

Discussion 0

Correct Answer: A Vote an answer

Question 12

A Storage Group containing the source volumes on a VMAX3 array is managed by the Gold Service Level. A TimeFinder SnapVX snapshot of this Storage Group is linked to the target volumes. The Storage Group containing the target volumes is managed by the Bronze Service Level.
Which Service Level will be used to manage the snapshot deltas?

A. Optimized B. None C. Gold D. Bronze

Discussion 0

Correct Answer: A Vote an answer

Question 13

What is a consideration for autoprovisioning groups on VMAX3 arrays?

A. A port may only belong to one Port Group B. An initiator may only belong to one Initiator Group C. Maximum number of levels of cascading permitted in a Storage Group is 64 D. A device cannot belong to more than one Storage Group

Discussion 0

Correct Answer: B Vote an answer

Question 14

When using TimeFinder SnapVX, why would a redirection-write be changed to a copy-on-write?

A. Improve wear rates on flash disks B. Prevent a new write from being demoted to a lower tier C. Snapshot delta has used 80% of the SRP D. Back-end utilization exceeds 80%

Discussion 0

Correct Answer: C Vote an answer