EMC Dell VxRail Deploy - D-VXR-DY-01 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

Which software is included with VxRail and provides continuous replication of virtual machines deployed on a VxRail appliance?

A. Dell EMC RecoverPoint for VMs B. VMware VM Snapshots C. VMware vSphereData Protection D. Dell EMC RecoverPoint CRR

Discussion 0

Correct Answer: A Vote an answer

Question 2

What action is required to enable VxRail Manager the ability to update system software and browse VxRail KB articles?

A. Configure Proxy settings B. Set the Username and Password for the Support Account C. Set the appliance status to 'Installed' in the Dell EMC Install database D. Enable Secure Remote Support (SRS)

Discussion 0

Correct Answer: B Vote an answer

Question 3

What are the minimum requirements for a customer-supplied VDS in a VxRail deployment?

A. 4 uplinks
Port groups for Discovery, Management, vMotion, and vSAN only B. 4 uplinks
Port groups for Discovery, Management, vCenter Server, vMotion, and vSAN C. 2 uplinks
Port groups for Discovery, Management, vCenter Server, vMotion, and vSAN D. 2 uplinks
Port groups for Discovery, Management, vMotion, and vSAN

Discussion 0

Correct Answer: C Vote an answer

Question 4

What must be enabled on ToR switch ports connected to VxRail nodes to support multiple VLANs?

A. Trunk Mode B. Rapid Spanning Tree C. Access Mode D. Link Aggregation

Discussion 0

Correct Answer: A Vote an answer

Question 5

An implementation engineer places a VxRail node into maintenance mode using the Ensure accessibility setting.
What is the engineer likely planning to do?

A. Shutdown of an entire cluster B. Temporary maintenance C. Extensive maintenance D. Permanent removal of host from cluster

Discussion 0

Correct Answer: B Vote an answer

Question 6

An implementation engineer logs in to the vSphere Client of a recently deployed VxRail cluster. They want to review the firmware versions on the VxRail nodes.
Which view should they use to gather this information?

A. Hosts and Clusters > VxRail Cluster > Monitor > VxRail > Appliances B. Host and Clusters > VxRail Host > Monitor > VxRail > Physical View C. Hosts and Clusters > VxRail Host > Configure > VxRail > iDRAC Configuration D. Hosts and Clusters > VxRail Cluster > Configure > VxRail > System

Discussion 0

Correct Answer: B Vote an answer

Question 7

For which typical activity would the No data migration setting be used when placing a VxRail host into maintenance mode?

A. Shutting down an entire cluster B. Temporary maintenance C. Permanently removing host from cluster D. Relocating host to remote data center

Discussion 0

Correct Answer: A Vote an answer

Question 8

A VxRail cluster 4.7.xxx environment is managed by the internal vCenter Server. An implementation engineer plans to deploy a new VxRail cluster using the existing vCenter Server instance, then use the customer-supplied VDS to manage both VxRail clusters.
What must be done?

A. Migrate the internal vCenter Server to an external vCenter Server, then upgrade the VxRail 4.7.xxx to 7.0.100 B. Upgrade the internal vCenter Server to version 7.0 C. Upgrade the VxRail version from 4.7.xxx to 7.0.000 D. Migrate the internal vCenter Server to an external vCenter Server, then merge the PSC

Discussion 0

Correct Answer: A Vote an answer

Question 9

What Is a supported method for racking nodes for a new VxRail deployment?

A. In the rack hosting the network equipment used to manage the iDRAC B. Starting with node 1 at the top of the rack C. With server exhaust facing the cold aisle D. With PDUs connected to 120v single phase 5-amp electrical circuits

Discussion 0

Correct Answer: B Vote an answer

Question 10

Which two iDRAC settings must be set before running the VxRail Deployment Wizard? (Choose two.)

A. Enable IPMI over LAN to Enabled B. NIC selection to Dedicated C. Channel Privilege Level Limit to Operator D. Auto Negotiation to Off

Discussion 0

Correct Answer: A,B Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).