EMC Dell PowerEdge Professional - DCPPE-200 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

An engineer needs to limit the power consumption of a chassis without powering down any server nodes.
Which step should the engineer take to perform this task?

A. Use the iDRAC to configure the System Input Power Cap for the chassis B. Use the CMC to configure the Power Cap Policy for each server node C. Use the iDRAC to configure the Power Cap Policy for each server node D. Use the CMC to configure the System Input Power Cap for the chassis

Discussion 0

Correct Answer: C Vote an answer

Question 2

AN engineer needs server 1 in the chassis to be able to communicate on the default untagged VLAN 1 and tagged VLANs 10, 20, and 50. The engineer has port 1 configured with the following settings:
interface TenGigabitEthernet 0/1
mtu 12000
switchport
vlan tagged 10,20,50
flowcontrol rx on tx off
During testing, the engineer is unable to communicate with anything on VLAN 1.
How should the engineer fix this issue?

A. Configure port 1 as a hybrid port B. Disable all flowcontrol C. Change the default untagged VLAN and tag VLAN 1 D. Set the MTU to default of 1500

Discussion 0

Correct Answer: D Vote an answer

Question 3

Refer to the exhibit.
An engineer needs to configure iSCSI boot on a blade and the iSCSI boot is NOT working.
Which two steps should the engineer take to fix the issue?

A. Verify the IP address of the target and initiator. Validate default gateway settings on the initiator. B. Modify the boot LUN ID on the target. Validate default gateway settings on the initiator. C. Change the IQN of the initiator. Verify the IP address of the target and initiator. D. Update the DNS server entries on the initiator. Change the IQN of the initiator.

Discussion 0

Correct Answer: A Vote an answer

Question 4

An engineer needs to re-purpose the storage of the chassis. Data must be lost when a drive fails. The configuration needs to allow for redundancy with the maximum amount of usable space.
What should the engineer create to perform this task?

A. RAID 60 B. RAID 6 C. RAID 50 D. RAID 5

Discussion 0

Correct Answer: B Vote an answer

Question 5

An engineer is installing two PCIe NICs into an existing VRTX chassis. Node 1 has three PCIe cards assigned to it already. After installation, the engineer is unable to assign the two new NICs to node 1.
What should the engineer do to assign the two PCIe NICs to node 1?

A. Power off the node B. Reseat the NICs C. Update the CMC firmware D. Upgrade the license

Discussion 0

Correct Answer: C Vote an answer

Question 6

An engineer has a new blade chassis that is 3/4 full. The chassis has six power supplies. The chassis at peak power usage needs at minimum four power supplies. Redundancy is NOT a concern.
The engineer needs a policy to meet the current needs and provide enough power to a fully populated chassis.
Which policy should the engineer choose?

A. N+2 B. N+N C. N+1 D. N+0

Discussion 0

Correct Answer: D Vote an answer

Question 7

An engineer is running an inventory report on a VRTX chassis group for a customer. When the engineer views the report, the engineer notices the inventory of one of the VRTX is missing one of its nodes.
What is the cause?

A. The node's iDRAC needs to have an Enterprise license installed. B. The node's iDRAC is unreachable from the VRTX group leader's CMC. C. The VRTX group member is in Chassis Power State Off since the node was inserted. D. The VRTX group member is disconnected from the network at the time of the report.

Discussion 0

Correct Answer: B Vote an answer

Question 8

An engineer needs to put chassis switches on a LAN that has already been configured for latency sensitive applications and to enable lossless links.
How should the engineer accomplish this?

A. dcd-input pfc B. iscsi enable C. enable perf enhance D. flowcontrol rx on tx off

Discussion 0

Correct Answer: D Vote an answer

Question 9

An engineer is installing a known good PCIe storage adapter in SLOT 1 of an FX2 chassis with four half height nodes. Node 1 is NOT detecting the adapter.
What must the engineer do so that node 1 can detect the adapter?

A. Power off node 1 B. Perform virtual reseat of the adapter C. Assign SLOT 1 to node 1 in the CMC D. Move the adapter to SLOT 7

Discussion 0

Correct Answer: D Vote an answer

Question 10

An engineer needs to configure a redundant CMC network link into to a newly installed FX2 chassis. CMC port 1 is up and working. The engineer only has one management switch available for CMC connections. The engineer plugs CMC port 2 into the management switch and leaves the data center. The network engineer reports extreme traffic on the network and is unable to connect to any other switches.
How should the engineer fix this problem quickly and maintain redundancy?

A. Add a second stacked management switch and connect CMC port 2 to the new switch B. Configure the FX2 CMC ports for redundancy in the console C. Configure spanning tree on the management switch D. Console into the CMC and reset to factory default settings

Discussion 0

Correct Answer: A Vote an answer