EMC Specialist - Implementation Engineer, NetWorker - E20-593 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

A customer is adding new tape devices to an EMC NetWorker server.
The command is issued to scan for devices but does not find the new devices.
What is the most likely cause?

A. Local device bootstrap has not been configured on the hard drive. B. Devices have not been added at the OS level. C. Devices are not initialized until jbconfig has been initiated. D. PAX translation mini-driver has not been installed.

Discussion 0

Correct Answer: B Vote an answer

Question 2

Your customer is running an EMC NetWorker 7.6 server and wants to upgrade their clients running NetWorker 7.4.
What are two ways to do this remotely from the NetWorker server?

A. Software Administration Wizard and nsrpush B. Software Administration Wizard and nsrclient C. Copy and nsrpush D. Copy withClients and nsrpush

Discussion 0

Correct Answer: A Vote an answer

Question 3

Your task is to develop a backup-to-disk solution for your client. After an initial analysis, you decide to include one EMC Disk Library (EDL) to be used as the primary backup device.
The customer has been using a physical library with LTO-3 drives for many years and would like to have the capability to recover from the old tape. The solution must result in the fewest possible changes to the EMC NetWorker server.
How can you best address these requirements?

A. Migrate all data from the outdated media to the new media format and archive. B. Install the IP replication agent on the backup server that controls the physical library.
Copy physical tapes over the network to virtual tapes to the EDL. C. Create a new data zone offsite to be used for recovery purposes only. Connect the physical library to the new zone and make it available to both locations. D. Connect the existing library to the back end of the EDL. Create a virtual library and drives that match the physical drive types.

Discussion 0

Correct Answer: D Vote an answer

Question 4

Which EMC NetWorker process coordinates all scheduled backups?

A. nsrmmdbd B. nsrjobd C. nsrindexd D. nsrd

Discussion 0

Correct Answer: B Vote an answer

Question 5

What EMC NetWorker command is used to display a list of labeled volumes in the
NetWorker media database?

A. nsrim B. mmlocate C. mminfo D. nsrmm

Discussion 0

Correct Answer: C Vote an answer

Question 6

Click the Calculator icon in the upper left-hand corner.
In an EMC NetWorker environment, the customer is backing up 7.5 TB per day. The 7.5 TB is comprised of 750 million files. According to EMC best practices, approximately how large will the Client File Index (CFI) be?

A. 167 GB B. 307 GB C. 209 GB D. 70 GB

Discussion 0

Correct Answer: A Vote an answer

Question 7

A Dell EMC NetWorker server has been configured to stage from an AFTD upon reaching a high water mark of 80%. After the staging begins, which rule determines when the staging process ends?

A. File system utilization reaches the low water mark B. All save sets older than the "max storage period" are moved C. All save sets over a specified size are moved D. Capacity used falls to any point below the high water mark

Discussion 0

Correct Answer: A Vote an answer

Question 8

A Dell EMC NetWorker backup administrator wants to identify bottlenecks for a file server with poor backup performance. The administrator discovers that Client Direct is disabled for the file server.
What happens when Client Direct is enabled?

A. Backup data is sent directly to the target device and metadata is sent to the NetWorker server B. Backup data and metadata are sent to the storage node and then to the target device C. Backup data is sent to storage node and metadata is sent to the NetWorker server D. Backup data is sent directly to the target device and metadata is sent to the storage node

Discussion 0

Correct Answer: C Vote an answer

Question 9

In a Microsoft Windows environment, what is a characteristic of a bare metal recovery when using Dell EMC NetWorker?

A. Can be used for recovery of NetWorker server databases B. Restores only the operating system C. Can be used to restore individual files D. Required when a host encounters a catastrophic failure

Discussion 0

Correct Answer: A Vote an answer

Question 10

What are the default target and maximum session settings for an AFTD?

A. Target sessions is 4 and default maximum sessions is 512. B. Target sessions is 1 and default maximum sessions is 32. C. Target sessions is 8 and default maximum sessions is 512. D. Target sessions is 2 and default maximum sessions is 256.

Discussion 0

Correct Answer: B Vote an answer

Question 11

In an EMC NetWorker environment, you are required to keep media in drives for only 10 minutes after completion of backup. What parameter must be set?

A. Unload sleep B. Idle device timeout C. Withdraw timeout D. Operation timeout

Discussion 0

Correct Answer: B Vote an answer

Question 12

The mode of an EMC NetWorker volume was prematurely set to "full". Which command can be used to change the status of the volume to "appendable"?

A. nsrim B. mmlocate C. mminfo D. nsrmm

Discussion 0

Correct Answer: D Vote an answer

Question 13

An EMC NetWorker administrator wants to find all the files within a save set that are still browsable by the client. Which command will allow the administrator to perform this task?

A. inquire B. nsrinfo C. nsrls D. mminfo

Discussion 0

Correct Answer: B Vote an answer

Question 14

What is a characteristic of Dell EMC NetWorker MEDITECH backups?

A. Integrates with the Backup Facilitator B. Only supports integrated serverless backups C. Supports remote replicas without requiring RecoverPoint D. Only supports tape and Data Domain devices

Discussion 0

Correct Answer: C Vote an answer

Question 15

Refer to the exhibit.

The calendar shows the level backup that was taken on each day. Which data is sent to the backup server on Friday's backup?

A. All changes since Wednesday B. All changes since Tuesday C. All changes since Monday D. All changes since Thursday

Discussion 0

Correct Answer: B Vote an answer