HP Migrating &Troubleshooting Enterprise Networks - HP0-Y37 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

What is a characteristic of load balancing in RRPP?

A. overlapping RRPP rings B. multiple RRPP domains sharing the same ring C. multiple RRPP rings within a domain D. multiple RRPP domains with different root priorities E. It is not possible to load balance with RRPP.

Discussion 0

Correct Answer: B Vote an answer

Question 2

Click the Exhibit button.

Which statements are true about the configuration of the switch shown in the exhibit? (Select two.)

A. The ?6?refers to an RRPP instance. B. The control VLAN for a Subordinate ring is VLAN 4092. C. The control VLAN for all rings is VLAN 4091. D. The ?6?refers to an MSTP instance. E. The ?6?refers to VLAN 16. F. Only RRPP control data are allowed in the protected VLAN.

Discussion 0

Correct Answer: B,D Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 3

Which statements are true about DHCP Snooping? (Select two.)

A. The DHCP Snooping binding table contains information about hosts interconnected with a trusted interface. B. When configuring DHCP Snooping on a switch, you define which ports are trusted to receive DHCP offers. Typically uplinks of a switch are trusted and Edge ports are untrusted. C. DHCP Snooping is when a switch acts as a DHCP server for end nodes that connect to that particular switch. This way, end nodes always get an IP address. D. DHCP Snooping is a malicious attack against the DHCP servers. E. DHCP Snooping prevents end nodes from receiving IP address assignments from an unauthorized DHCP server. F. DHCP Snooping is a Cisco Proprietary protocol. The standard is not yet ratified.

Discussion 0

Correct Answer: B,E Vote an answer

Question 4

Click the Exhibit button.

A customer has a Cisco-based network, and you are replacing the distribution layer switches with HP E-Series switches. The customer wants you to perform the migration with as little downtime as possible, and you plan to connect the E-Series switches temporarily in parallel with the current distribution switches, as shown in the exhibit. As part of the migration, the customer wants you also to migrate the remaining Cisco switches to open-standard protocols rather than the proprietary Cisco ones, which the exhibit shows that these switches currently use.Which Cisco proprietary protocol should you wait to migrate until after you remove the Cisco distribution switches in order to avoid connectivity issues?

A. Rapid Per-VLAN Spanning Tree Plus (Rapid PVST+) to Multiple Spanning Tree Protocol (MSTP) B. VLAN Trunking Protocol (VTP) to static VLANs C. Cisco Discovery Protocol (CDP) to Link Layer Discovery Protocol (LLDP) D. Extended Interior Gateway Routing Protocol (EIGRP) to Open Shortest Path First (OSPF)

Discussion 0

Correct Answer: A Vote an answer

Question 5

Click the Exhibit button.
You have been asked to troubleshoot a problem in a multi-area OSPF network. Users connected to R3 are not able to access any destinations outside of Area 1. The Area 1 configurations for the R1 and R3 routers are shown below. Which configuration change should be made to correct this problem?

A. Option B B. option A C. Option E D. Option C E. Option D

Discussion 0

Correct Answer: A Vote an answer

Question 6

RRPP statistics for an HP A-Series switch indicate that Hellos are being received on the secondary port but do not indicate that Hellos are being sent on the primary port. What most likely caused this?

A. The switch is in Edge node mode. B. A link-down message has been sent by the Master node. C. The primary port is down. D. The RRPP ring is in a fail state. E. The switch is in Transit node mode.

Discussion 0

Correct Answer: E Vote an answer

Question 7

You are installing a new HP. A-Series switch to an existing Cisco network running the following VLANs: management (VLAN id 1), sales (VLAN id 2), engineering (VLAN id 3), HR (VLAN id 4).

Engineering users connected to an HP switch are complaining that they are unable to access engineering resources connected to the Cisco switch?Which configuration change will correct this problem?

A. [HP-GigabitEthernet1/0/24]port trunk pvid vlan 2 B. [HP-GigabitEthernet1/0/24]port trunk permit vlan all C. Cisco(config-if)#switchport trunk allowed vlan all D. Cisco(config-if)#switchport trunk native vlan 3

Discussion 0

Correct Answer: D Vote an answer

Question 8

Click the Exhibit button.After examining the IP RIP configuration of Router 1, the administrator enters the following commands:

Now, the administrator must configure Router 1 to advertise the following networks to AS-65002 using BGP:

No other subnets of 64.0.0.0/8 should be advertised.Which configuration change will achieve the desired result?

A. [Router-1]ip ip-prefix list index 10 deny 64.0.0.0 24ip ip-prefix list index 20 permit 64.0.0.0 22ip ip-prefix list index 30 deny 0.0.0.0 0 less-equal 32 B. [Router-1]ip ip-prefix list index 10 permit 64.0.1.0 24 greater-equal 24ip ip-prefix list index 20 permit 64.0.2.0 24 greater-equal 24ip ip-prefix list index 30 permit 64.0.3.0 24 greater-equal 24 C. [Router-1]ip ip-prefix list index 10 permit 64.0.1.0 24ip ip-prefix list index 20 permit 64.0.2.0 23ip ip-prefix list index 30 deny 64.0.0.0 8 D. [Router-1]ip ip-prefix list index 10 deny 64.0.0.0 24ip ip-prefix list index 20 permit 64.0.0.0 22 greater-equal 24 less-equal 24 E. [Router-1]ip ip-prefix list index 10 permit 64.0.1.0 24ip ip-prefix list index 20 permit 64.0.0.0 22ip ip-prefix list index 30 deny 64.0.0.0 8

Discussion 0

Correct Answer: D Vote an answer