HP Aruba Certified Switching Associate - HPE6-A41 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

Refer to the exhibit.

The student A client needs to connect to FTP Server B.
Student A sends the necessary ARP request and receives a reply.
Which destination MAC address does the Student A client use in the FTP packet to FTP Server B?

A. 00-1D-B3-F1-EF-40 B. 00-E0-52-F0-41-B2 C. 00-1D-B3-F1-EF-31 D. 00-E0-52-F0-44-87

Discussion 0

Correct Answer: A Vote an answer

Question 2

A network administrator needs to complete the initial setup on an ArubaOS switch with the use of remote access. How can the network administrator do this?

A. Set up the network DHCP server to assign the switch a reserved IP address. Connect the switch to a VLAN with DHCP services and then establish a Telnet session to the reserved IP address. B. Connect the switch's OOBM port to the same VLAN as the management station, and then establish a Telnet session to the switch default IP address. C. Send a Reverse ARP from the management station and assign a temporary IP to the workstation. D. Connect the switch's OOBM port to the same VLAN as Aruba AirWave. Then manually discover the switch in AirWave using the switch default IP address.

Discussion 0

Correct Answer: D Vote an answer

Question 3

What does the traceroute command that is entered on an ArubaOS switch identify?

A. each physical device between the switch and a destination B. the path to each router connected to the switch C. each Layer 3 device between the switch and a destination D. debug output tracing entries to the routing table

Discussion 0

Correct Answer: C Vote an answer

Question 4

What is a valid setup for a Virtual Switching Framework (VSF) fabric?

A. one 5412R zl2 switch as commander and two 5406R zl2 switches as standby members B. one 5406R zl2 switch as commander and two 5412R zl2 switches as standby members C. one 5406R zl2 switch as commander and one 5412R zl2 switch as a standby member D. one 5412R zl2 switch as commander and one 5412R zl2 switch as a standby member

Discussion 0

Correct Answer: D Vote an answer

Question 5

Refer to the exhibit.

Based on the topology shown in the exhibit, which symptom does a network administrator see if the ArubaOS switches are in their factory default states?

A. Mislearned MAC addresses B. Ports places in a blocking state C. Layer 3 loop D. TTL expired in transit

Discussion 0

Correct Answer: C Vote an answer

Question 6

A network administrator has copied new software to an ArubaOS switch and placed this software in the secondary ash location. The switch is currently booting from the primary location. The administrator wants the switch to start using the new software.
What should the administrator do to accomplish this?

A. Rename the secondary software as the primary software. B. Reboot the switch, which automatically causes the switch to use the newer software. C. Copy the secondary software to the primary software slot. D. Execute the command to boot the system from the secondary flash.

Discussion 0

Correct Answer: D Vote an answer

Question 7

An ArubaOS switch operates at factory default settings. A network administrator enters this command:
Switch (config)# password operator plaintext mysecret
How does the switch now control access to the CLI through the console port?

A. It allows users to access basic mode without logging in, but forces them to enter password mysecret to reach enable mode. B. It forces users to enter no username and password mysecret to gain access to basic mode. Users can then reach enable mode without authenticating. C. It forces users to enter no username and password operator to gain access to basic mode. Users must then enter password mysecret to reach enable mode. D. It forces users to enter username operator and password mysecret to gain access to basic mode. Users can then reach enable mode without authenticating.

Discussion 0

Correct Answer: A Vote an answer

Question 8

A network administrator uses the console to access an ArubaOS core switch and wants to find the management IP address of another ArubaOS switch that is currently connected to port B1. Which information should the administrator review?

A. device profile with the use of the show device-profile status command B. interface with the use of the show interface command C. LLDP with the use of the show lldp info remote-device command D. ARP with the use of the show arp command

Discussion 0

Correct Answer: C Vote an answer

Question 9

Refer to the exhibit.

This switch currently assigns all VLANs to MSTP instance 0 or the Internal Spanning Tree (IST).
Which statement correctly describes interface 21?

A. The interface does not forward or accept data traffic, but it is ready to start forwarding if interface 19 fails. B. The interface is an edge port but has received Bridge Protocol Data Units (BPDUs), so it is disabled. C. The interface is down at Layer 2; it is not available for sending or receiving any traffic. D. The interface does not support spanning tree: it is possible that it will introduce a loop in the network.

Discussion 0

Correct Answer: A Vote an answer