HP Delta-Aruba Certified Switching Professional - HPE6-A46 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

Refer to the exhibits.
Exhibit 1

Exhibit 2

The company wants to minimize congestion on Link 1. Which spanning tree implementation meets this goal?

A. Instance 1 = VLANs 4-5 Instance 2 = VLANs 6-7Switch 2 instance 1 priority = 0 Switch 2 instance 2 priority = 1Switch 3 instance 1 priority = 0 Switch 3 instance 2 priority = 1 B. Instance 1 = VLANs 4-5 Instance 2 = VLANs 6-7Switch 2 instance 1 priority = 0 Switch 2 instance 2 priority = 1Switch 3 instance 1 priority = 1 Switch 3 instance 2 priority = 0 C. Instance 1 = VLANs 4,6 Instance 2 = VLANs 5,7Switch 2 instance 1 priority = 0 Switch 2 instance 2 priority = 1Switch 3 instance 1 priority = 0 Switch 3 instance 2 priority = 1 D. Instance 1 = VLANs 4,6 Instance 2 = VLANs 5,7Switch 2 instance 1 priority = 0 Switch 2 instance 2 priority = 1Switch 3 instance 1 priority = 1 Switch 3 instance 2 priority = 0

Discussion 0

Correct Answer: D Vote an answer

Question 2

A network administrator can set the OSPF metric-type on an AOS-Switch to Type 1 or Type 2. What is the difference?

A. A Type 2 metric assigns cost 1 to a 100 Gbps link, while a Type 1 metric assigns cost 1 to all links of
100 Mbps or higher. B. A Type 2 metric marks external routes that can be advertised in NSSAs, while a Type 1 metric marks external routes that can only be advertised in normal areas. C. A Type 2 metric stays the same as the external route is advertised, while a Type 1 metric increments with internal OSPF link costs. D. A Type 2 metric is assigned to multiple external routes that are aggregated together, while a Type 1 metric does not permit external route aggregation.

Discussion 0

Correct Answer: C Vote an answer

Question 3

Refer to the exhibits.
Exhibit 1

Exhibit 2

Which change to the environment would cause clients to fail to receive DHCP settings?

A. the addition of a new VLAN on the link aggregation between Switch-1 and Switch-2 B. a change of IP address on the network DHCP server C. the addition of a new link to the link aggregation between Switch-1 and Switch-2 D. a change in the Switch-1 option 82 policy to replace

Discussion 0

Correct Answer: D Vote an answer

Question 4

How far do OSPF link state updates (LSUs) for Type 1 (Router) and Type 2 (Network) LSAs propagate?

A. to every OSPF router in the local area B. to every OSPF router in the local area and the backbone C. to every OSPF router in the network to which the LSU applies D. to every OSPF router in all areas

Discussion 0

Correct Answer: D Vote an answer

Question 5

An AOS-Switch enforces 802.1X authentication to an Aruba ClearPass server. A user connects but cannot receive network access, even though the ClearPass administrator finds an Access-Accept for the user on this switch. The switch administrator suspects that there is an issue with the dynamic settings returned by ClearPass.
Where should the administrator look for information about these settings?

A. in the detailed RADIUS server statistics B. in the running-config for the interface C. in the interface statistics D. in the details for port-access clients

Discussion 0

Correct Answer: D Vote an answer

Question 6

A company has a wireless Aruba solution and wired users that connect to AOS-Switches. The company wants deep insight into the types of applications that wired users run. The company also wants more control over the traffic.
What can the company do to meet these goals?

A. Configure extended IP ACLs on the AOS-Switches to filter the traffic. B. Configure RMON receivers on the switches. C. Set up remote traffic mirroring between the AOS-Switches and Aruba Mobility Controllers. D. Use tunneled node to send traffic through an Aruba Mobility Controller

Discussion 0

Correct Answer: D Vote an answer

Question 7

Refer to the exhibit.

An administrator created a backplane stack with the plug-and-play method, and did not alter the default backplane stacking settings. Later, two backplane stacking links failed, as shown in the exhibit.
What happens to the backplane stack after the failures?

A. The fragment that contains the commander operates at Layer 2 and Layer 3, and the other fragment operates at Layer 2 only. B. The standby becomes the commander of its fragment, which remains active. The fragment with the commander becomes inactive. C. The standby becomes the commander of its fragment. Both fragments remain active and operate at both Layer 2 and Layer 3. D. The fragment that contains the commander remains active, and the fragment with the standby member is disabled.

Discussion 0

Correct Answer: C Vote an answer

Question 8

What is a reason for hello packets between two OSPF routers?

A. to permit OSPF to operate between two routers that also run VRRP B. to establish an area that is not directly connected to the backbone Area 0 C. to permit an OSPF adjacency between two VSF fabrics D. to monitor connectivity with the neighbor, but not exchange the routing table

Discussion 0

Correct Answer: D Vote an answer