IBM AIX 7 Administration - C4040-221 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

Why does the following ksh code segment fail to run?

A. An alphanumeric operator is being used to compare the integer variable. B. The 'if statement must be terminated with an 'end1 keyword. C. The 'elseif keyword is not valid within ksh scripts. D. The segment is missing an 'else' default statement.

Discussion 0

Correct Answer: C Vote an answer

Question 2

Which startup script will mount all filesystems in /etc/filesystems for which the mount parameter is set to 'true'?

A. /etc/rc.bootc B. /etc/red C. /etc/rc D. /sbin/rc.start

Discussion 0

Correct Answer: C Vote an answer

Question 3

What is required to support VLANs in an AIX partition?

A. IEEE 802.3ad compatible interface B. QoS must be enabled C. IEEE 802.1Q compatible adapter D. Promiscuous mode disabled

Discussion 0

Correct Answer: C Vote an answer

Question 4

An administrator is removing a failed disk from a mirrored rootvg volume group. A message directed the administrator to run the chpv -c command.
The administrator ran this command against the last available disk in rootvg.
What is the result of performing this action?

A. The failed drive is removed from the bootlist. B. The boot record was removed from the system. C. The boot record was updated with the available disk information. D. The ipldevice was re-linked to the available disk device name.

Discussion 0

Correct Answer: B Vote an answer

Question 5

A host is already configured to access the network, and the administrator would like to configure a second adapter on the same system. This adapter should be permanently
configured so that the new IP address is available when the system reboots. Which command should be used?

A. mktcpip B. ipconfig C. ifconfig D. chdev

Discussion 0

Correct Answer: D Vote an answer

Question 6

A customer has purchased two dual-port Fibre Channel and two dual-port Ethernet cards. Which configuration will provide the greatest amount of redundancy for two client partitions?

A. Assign each client one fibre and Ethernet card. Make sure they are cabled to a different network and fibre switches. B. Assign each client one port on each of the fibre and Ethernet cards. Cable each to a different network or fibre switch. C. Assign all resources to a VIO server. Create an Etherchannel on the network adapters that connect to different FCoE switches. D. Create a dual VIO server environment, each with one Ethernet and fibre card. Make sure each card is attached to a different network and fibre switch.

Discussion 0

Correct Answer: D Vote an answer

Question 7

One disk within a mirrored rootvg volume group failed and was replaced. What is the first action the administrator must take after re-establishing mirroring?

A. Recreate/dev/ipldevice. B. Re-enable volume group quorum. C. Copy/dev/hd5 to the new disk. D. Create the boot image on the replaced disk.

Discussion 0

Correct Answer: D Vote an answer

Question 8

An LPAR is configured with strict logical volume mirroring across two disks for resilience. The administrator would like to ensure if one disk fails the volume group stays online. Which command will ensure that the datavg volume group stays online?

A. chvg -Qn datavg B. mirrorvg-Q-c 2 datavg C. varyonvg -n datavg D. mklvcopy -e m -s y (each logical volume name) 2

Discussion 0

Correct Answer: A Vote an answer

Question 9

Based on the following output, what must be done if loglv1 name is changed to db2loglv?

A. Run the chvg command to update volume group default logging logical volume to db2loglv. B. Run the logform command to update the log format of db2loglv. C. Run the chlv command to update dblv01 logging logical volume to db2loglv. D. Run the chfs command to update /exportfs/db01 logging logical volume to db2loglv.

Discussion 0

Correct Answer: C Vote an answer

Question 10

An administrator has logged in as root but is unable to run the ksh script named rperf. Given the following information, how could this be fixed?

A. Change the file to be of extension ksh B. Change the owner of the script to root C. Change the parent directory to be executable D. Change the permissions to 700

Discussion 0

Correct Answer: D Vote an answer