Network Appliance NetApp Certified Storage Installation Engineer - ONTAP 9.1 - NS0-181 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

Select the Exhibit tab.

You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.1 on a customer site.
Referring to the exhibit, which two statements describe what is required to get an HA cabled system? (Choose two.)

A. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 4, then cable the out-of-band ACP. B. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 4, then cable the out-of-band ACP. C. Insert a cable from left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3. D. Insert a cable from right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3.

Discussion 0

Correct Answer: A,D Vote an answer

Question 2

You are configuring a new system with ONTAP 9.1. You created interface groups, VLANs, and a broadcast domain for the new ports on all the nodes of your cluster. During the configuration, you used an MTU value of
1500 for the broadcast domain and 9000 for the physical ports. The customer asks you to enable jumbo frames.
What should you do in this scenario?

A. Set the MTU option to jumbo frames on the ifgroup. B. Set the MTU option to jumbo frames on the broadcast domain. C. Change the MTU value to 9000 on the broadcast domain. D. Change the MTU value to 9000 on the ifgroup.

Discussion 0

Correct Answer: C Vote an answer

Question 3

What is a valid failover policy for a SAN LIF?

A. local-only B. system-define C. disabled D. broadcast-domain-wide

Discussion 0

Correct Answer: D Vote an answer

Question 4

Your customer has filled out the customer installation worksheet. However, the customer's network environment is not set up and ready for the new ONTAP 9.1 system. The customer requests that you install the system and states that they will finish the configuration when they have acquired the appropriate network connections.
Which two statements are correct about this scenario? (Choose two.)

A. A cluster can be created without data network connections, but it must include a cluster interconnect connection. B. You should cable all of the controllers and disk shelves, power on the system, and then leave the system as-is for the customer to configure. C. You should cable a cluster so that the clusters interconnect traffic is on a separate network from all other traffic. D. You cannot install an ONTAP system without having the customer network configuration.

Discussion 0

Correct Answer: A,C Vote an answer

Question 5

You were dispatched to add a DS224C to an existing HA pair that has a stack of DS4243 shelves with 1 TB drives and a stack of DS4246 shelves with 1 TB drives. The customer wants to make sure that ACP is cabled for all shelves.
Which two considerations should you advise the customer in this situation? (Choose two.)

A. ACP communication cannot be used for the DS224C and the DS4243 shelves at the same time. B. The ACP communication has been discontinued beginning with ONTAP 9.1, IOM6, and IOM12 modules. C. Out-of-band ACP communication is use by default in ONTAP 9.0 and later software. D. ACP communication uses SAS cables and does not require Ethernet cables for IOM12 and IOM6 modules.

Discussion 0

Correct Answer: C,D Vote an answer

Question 6

After an installation, your customer asks you if you have a solution or a product that can easily list all the elements of a running ONTAP cluster, and highlight the changed and new objects including IP addresses, subnets, IPspaces, SVMs, volumes, and LUNs. For easy modification the output should be a document or a spreadsheet. Your customer does not have any PowerShell or scripting knowledge.
In this scenario, which Windows PowerShell-based NetApp tool would help to extract this information?

A. NetApp Synergy B. NetAppDocs C. NetApp Management SDK D. NetApp PowerShell Toolkit

Discussion 0

Correct Answer: D Vote an answer

Question 7

Referring to the exhibit, which statement describes the duster network used by the cluster interconnect ports?

A. The network used to allow all nodes to communicate with the users for data access. B. The network that allows all nodes in the cluster to have direct access to every other node's disk shelves. C. The network used to allow all nodes to communicate for internal (private) data access. D. The network used to allow all nodes to communicate with the customer (or management access.

Discussion 0

Correct Answer: C Vote an answer

Question 8

A customer buys a new switchless ONTAP 9.1 FAS2650 cluster. You are asked to install the system at the customer's site.
Which three steps are needed to accomplish this task? (Choose three.)

A. Cable the ACP. B. Connect both power cords. C. Cable the controller for switchless ONTAP software. D. Cable the cluster-interconnect to the CN1610 switches. E. Install the system in the rack.

Discussion 0

Correct Answer: B,C,E Vote an answer

Question 9

A customer wants to reduce the disk allocation requirement for the root aggregate and increase usable storage by partitioning the disks into one large part and one small part. The small part is used for the root aggregate and the large part for the data aggregates.
In this situation, what is this feature called?

A. ONTAP B. storage virtual machine C. RAID D. Advanced Drive Partitioning

Discussion 0

Correct Answer: D Vote an answer