Network Appliance NetApp Certified Storage Installation Engineer, ONTAP - NS0-182 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

You are deploying a cluster with four AFF A300 nodes and Cisco 3232C switches. When you arrive at the customer's site, you notice that there are multiple breakout cables and four Cisco 3232C switches.
In this scenario, which statement is true?

A. Your customer ordered a MetroCluster IP configuration. B. Cisco best practices require four Cisco 3232C switches for high availability. C. A 4-node AFF A300 cluster requires two Cisco 3232C switches for the cluster interconnect and two for management. D. A 4-node AFF A300 cluster requires four Cisco 3232C switches.

Discussion 0

Correct Answer: C Vote an answer

Question 2

Click the Exhibit button.

You are receiving AutoSupport e-mail from both controllers, but Active IQ is showing updates from only node cl-01-02.
Referring to the exhibit, what is a reason why Active IQ is receiving AutoSupport updates from only node cl-01-02?

A. A firewall rule is blocking the AutoSupport. B. The mail host is blocking the AutoSupport. C. The cluster management LIF is down. D. The service processor is not configured.

Discussion 0

Correct Answer: B Vote an answer

Question 3

Your customer has filled out the customer installation worksheet. However, the customer's network environment is not set up and ready for the new ONTAP 9.5 system. The customer requests that you install the system and states that they will finish the configuration when they have acquired the appropriate network connections.
Which two statements are correct about this scenario? (Choose two.)

A. A cluster can be created without data network connections, but it must include a cluster interconnect connection. B. You should cable all of the controllers and disk shelves, power on the system, and then leave the system as-is for the customer to configure. C. You should cable a cluster so that the clusters interconnect traffic is on a separate network from all other traffic. D. You cannot install an ONTAP system without having the customer network configuration.

Discussion 0

Correct Answer: A,C Vote an answer

Question 4

You are performing an automated upgrade of a 2-node cluster. Node-01 upgrades successfully. But during the node-02 upgrade, there is a power outage at the site. When power is restored and the nodes are booted, you receive this message: Warning: The Cluster is in a mixed version state. Update all of the nodes to the same version as soon as possible.
In this scenario, which command provides information that will help you understand the problem?

A. system node upgrade show-task-status B. system node upgrade-revert show C. system node image show D. system node image package show

Discussion 0

Correct Answer: D Vote an answer

Question 5

You create a LIF called svm_cifs_lif01 on a port that is already in an up state. After you test the storage failover, the LIF does not automatically revert to its home port.
In this scenario, what should you do to solve the problem?

A. Configure a new failover group. B. Add the port in a broadcast domain. C. Configure the LIF with the automatic revert option. D. Configure the LIF with the DHCP option.

Discussion 0

Correct Answer: C Vote an answer

Question 6

What is the maximum port speed of an Ethernet port on a Cisco Nexus 3232C cluster-interconnect switch?

A. 200GbE B. 10GbE C. 40GbE D. 100GbE

Discussion 0

Correct Answer: C Vote an answer

Question 7

Recently, your 2-node FAS8020 cluster was upgraded from ONTAP 8.3 to ONTAP 9.5. You have just added two FAS8060 nodes to the cluster. You have executed Config Advisor to verify your work. Config Advisor tells you that the cluster ports on the original two FAS8020 nodes have Flow Control set to FULL.
In this scenario, to what should the Flow Control setting on the FAS8020 ports be set?

A. Flow Control should be set to NONE. B. Flow Control should be set to ALL. C. Flow Control should be set to RECEIVE. D. Flow Control should be set to SEND.

Discussion 0

Correct Answer: B Vote an answer

Question 8

What are two types of load balancing methods available in multimode interface groups? (Choose two.)

A. broadcast domain-based load balancing B. port-based load balancing C. LIF-based load balancing D. IP-based load balancing

Discussion 0

Correct Answer: B,D Vote an answer

Question 9

A customer wants to reduce the disk allocation requirement for the root aggregate and increase usable storage by partitioning the disks into one large part and one small part. The small part is used for the root aggregate and the large part for the data aggregates.
In this situation, what is this feature called?

A. ONTAP B. storage virtual machine C. RAID D. Advanced Drive Partitioning

Discussion 0

Correct Answer: D Vote an answer

Question 10

After completing the installation of a DS224C shelf, you observe the error shown in the exhibit.
Which action should you take to troubleshoot the error? (Choose two.)

A. Re-seat the SAS card. B. Reconnect the SAS cable. C. Perform a takeover-giveback. D. Re-seat the IOM module.

Discussion 0

Correct Answer: B,D Vote an answer

Question 11

To ensure that your customer's cluster is robust and operational, you need to be familiar with configuration best practices.
Which three practice rules should you always follow? (Choose three.)

A. Use LIFs with defined failover policies. B. Remove failed disk drives once a year to maintain minimum interruption in your controller stability. C. Do not use the root aggregate for storing data. D. Keep all nodes in the cluster on the same version of ONTAP. E. All power supply units should be plugged into the same power grid.

Discussion 0

Correct Answer: A,C,D Vote an answer

Question 12

After you install a new cluster with ONTAP 9.5 software, you want to create a new broadcast domain. During the creation of the broadcast domain, you receive an error that there are no free ports available.
What is the reason for this error message?

A. You can create a new broadcast domain only within the CLI. B. By Default, all ports are bound to the "Default" broadcast domain. To create a new port, remove the needed ports from the "Default" broadcast domain. C. By Default, all ports are bound to the "Default" broadcast domain. To create a new port, remove the needed ports from the "Default" broadcast domain and create a new IPspace. D. Before you configure a new broadcast domain, you should create a new IPspace.

Discussion 0

Correct Answer: D Vote an answer