Oracle Solaris 10 System Administrator Certified Professional Upgrade - 1Z0-879 FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

You need to restore some files from a file system. The file system was backed up from a snapshot. Which command correctly restores these files?

A. snaprestore -i B. ufsrestore -i C. fssnap -r D. fssnap -i

Discussion 0

Correct Answer: B Vote an answer

Question 2

You accidently initiated an abort sequence. As a consequence, your SPARC-based system went into the PROM mode. Which two actions would disable the default keyboard abort sequence? (Choose two.)

A. Edit /etc/default/kbd to change the value of the variable KEYBOARD_ABORT to disable. B. Run the eeprom command to disable KEYBOARD_ABORT. C. Detach serial console device. D. In PROM mode, change the value of keyboard to disable. E. Run the kbd -a disable command

Discussion 0

Correct Answer: A,E Vote an answer

Question 3

As system administrator, you are asked to remove the SUNWaudd package from a user's workstation. When you run the command to remove this package, you see the following messages on your console:

What happens to the files associated with the SUNWauddx and SUNWusb packages if you continue with the removal operation?

A. Only the files shared with the SUNWaudd package are removed. B. The files remain on the system. C. The files are marked for removal, but are only removed after the next reboot. D. The files are removed.

Discussion 0

Correct Answer: B Vote an answer

Question 4

When modifying the Solaris boot behavior on an x86-based server, the modification can be permanent or temporary. Which describes the procedure used to change the boot behavior temporarily, for a single boot cycle, until the next time that the system is booted?

A. Edit the bootenv.rc file with the temporary boot command. B. Use the bootadm command to set the temporary boot command. C. Use the kernel command to set the temporary boot command. D. Use the eeprom command to set the temporary boot command. E. Modify the boot_archive file with the temporary boot command.

Discussion 0

Correct Answer: C Vote an answer

Question 5

Given:
# rpcinfo -p |grep rusersd 100002 2 tcp 32776 rusersd 100002 3 tcp 32776 rusersd 100002 2 udp 32786 rusersd 100002 3 udp 32786 rusersd
Which three statements are true? (Choose three.)

A. rusersd is registered with rpcbind. B. The process identifiers (pids) of rusersd are 32776 and 32786. C. rusersd uses TCP and UDP protocols. D. rusersd is currently using ports 32776 and 32786. E. rusersd always uses port 100002.

Discussion 0

Correct Answer: A,C,D Vote an answer

Question 6

You need to change the hostname and IP address of a server. Without manually editing all of the required files, which command can be run to restore a systems configuration to an unconfigured state, ready to be reconfigured again?

A. /usr/sbin/set_parms initial B. /sbin/ipconfig C. /usr/sbin/sys-unconfig D. /usr/sbin/unconfig

Discussion 0

Correct Answer: C Vote an answer

Question 7

Solaris 10 provides a tool to connect, over the internet, to a server at Sun Microsystems and analyze your system for security updates. Before you can fully utilize this tool, you must first register your Solaris 10 OS with Sun Microsystems. Which of the following commands will you use to register your software?

A. sconadm B. patchpro C. smpatch D. updatemanager

Discussion 0

Correct Answer: A Vote an answer

Question 8

Your x86-based Solaris server will not boot from the primary boot drive. Because the boot drive has been mirrored, you need to change the server so that the system boots from the alternate boot disk. Which answer describes the procedure to change the default boot disk?

A. Change the bootpath parameter in the bootenv. re file so that it points to the correct boot drive. B. Use the eeprom command to change the bootpath parameter so that it points to the correct boot drive. C. Change the bootpath parameter in the boot archive file so that it points to the correct boot drive. D. Use the bootadm command to change the bootpath parameter so that it points to the correct boot drive.

Discussion 0

Correct Answer: A Vote an answer

Question 9

You want to backup an active ZFS file system named dbase. When listing the information on the file system, the following information is displayed:

Rather than unmount the file system and make it unavailable during the backup, you want to create a point in time snapshot of the file system and backup that snapshot. Which command is used to create a point in time snapshot of the dbase file system?

A. zfs clone data/dbase data/sdbase/dbase_snapshot B. fssnap -F ufs -o bs=/var/tmp /data/dbase /dev/fssnap/0 C. zfs snapshot data/dbase@ dbase_snapshot D. zfs snapshot files/data data_snapshot

Discussion 0

Correct Answer: C Vote an answer