Pure Storage Certified FlashArray Implementation Specialist - FlashArray-Implementation-Specialist FREE EXAM DUMPS QUESTIONS & ANSWERS]

Question 1

An Implementation Engineer is performing an inventory for an NDU from a FlashArray//X70R2 to a FlashArray//X70R4 and discovers that a complete FlashArray//X70R4 was shipped instead of an NDU kit.
What is the minimum hardware the Implementation Engineer should use from the new array to complete the NDU?

A. Controllers B. Controllers and NVRAM C. Controllers and power supplies

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 2

An Implementation Engineer is going on site to complete a data pack evacuation and perform a hardware NDU.
At what step should the Implementation Engineer contact support for assistance?

A. Before starting the data pack evacuation process. B. After removing the fully evacuated drives and before proceeding with the hardware NDU. C. After removing the old drives and inserting any new ones, but before they rebuild. D. When the hardware NDU has been completely finished.

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 3

What are the default replication ports on all three rack unit FlashArray models?

A. ETH0 and ETH1 B. ETH4 and ETH5 C. ETH2 and ETH3

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 4

What upgrade scenario required an upgrade of power supplies?

A. X50R2 > X50R3 B. X50 > X70 C. X10 > X50

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 5

At the completion of an upgrade, which command is used to send phonehome logs?

A. purearray phonehome --send-today B. purelogs --send-all C. purearray phonehome --send-logs

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 6

During an intra-series upgrade from //XR3 to //XR4, which command should the Implementation Engineer run to verify host connectivity before removing the secondary controller?

A. host_connectivity --hosts B. iobalance --sampletime 30 C. purehost list --host | less D. purenetwork monitor --live

Discussion 0

Correct Answer: B Vote an answer

Question 7

On a FlashArray//XR20R2/3 Fibre Channel (FC) array, what is the default type and placement of the PCIe FC card?

A. 2-port in slot 0 B. 2-port in slot 2 C. 4-port in slot 0

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 8

The customer has completed the installation document and has stated that the proxy server address is
"10.24.18.120". What additional information is required?

A. Protocol prefix and credentials B. Protocol prefix and port number C. Credentials and port number

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 9

When updating Purity on a new array, which command should the Implementation Engineer run to start the process?

A. purereboot --install B. puresetup C. pureinstall

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 10

Which PCI cards must be validated on the Bill of Materials (BOM) to allow an Implementation Engineer to attach a DirectFlash Shelf to a FlashArray//XL130R5?

A. FA-XL-200G Ethernet/RoCE 2-Port B. FA-XL-100G Ethernet/RoCE 2-Port C. FA-XL-100G iSCSI/RoCE 2-Port

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 11

An Implementation Engineer runs check start validate-array-health before starting a FlashArray//X70R3 to FlashArray//X70R5 HWNDU and receives code 60 alert indicating an unhealthy NVRAM module in CH0.
NVB1. What action Should the Implementation Engineer take to resolve this?

A. Disable the unhealthy NVRAM module and proceed With HWNDU after confirming there is no degraded data. B. Reseat the unhealthy NVRAM module, and then verify it is in a healthy status prior to proceeding with the HWNDU. C. Proceed with the HWNDU, the //X70 model has a four NVRAM configuration so the array still has redundancy.

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 12

On FlashArray models that use standard DFMs instead of DFMDs, which NVRAM bays are always populated?

A. NVB0 and NVB3 B. NVB0 and NVB1 C. NVB0 and NVB2

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).

Question 13

An Implementation Engineer is onsite to add two 4-port FC cards to a FlashArray//X20R3. In what state should the controller be in before performing the card add procedure?

A. Secondary B. Standby C. Primary

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for FreeCram members. You can sign-up / login (it's free).