Prev Next Question 40/66 - NS0-182.v2020-02-08

After setting up a new cluster, you run an AutoSupport message for a test.
Which two commands would you use to proof the functionality and settings of AutoSupport? (Choose two.)

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Question List (66q)
Question 1: Which two statements are true about the ONTAP 9.5 networking...
Question 2: What is the maximum number of data disks that a RAID-TEC RAI...
Question 3: (Exhibit) You just installed two nodes into an existing ONTA...
Question 4: Select the Exhibit tab. (Exhibit) You install a new FAS2552 ...
Question 5: You just finish the installation of a single-node cluster. Y...
Question 6: Your customer has a new FAS2650 HA cluster with ONTAP 9.5 in...
Question 7: Select the Exhibit tab. (Exhibit) You install a new FAS2650 ...
Question 8: You must cable a new AFF A700 with two DS224C shelves that a...
Question 9: Which hot-swappable transceiver is required to obtain full p...
Question 10: You need to verify the configuration currently loaded on a C...
Question 11: You have just completed the installation of a FAS9000 HA pai...
Question 12: Your customer has filled out the customer installation works...
Question 13: Click the Exhibit button. (Exhibit) After running Config Adv...
Question 14: You want to grow your current ONTAP cluster. You have a Cisc...
Question 15: You create a LIF called svm_cifs_lif01 on a port that is alr...
Question 16: A customer wants you to add a new AFF A700 HA pair to an exi...
Question 17: What is the minimum number of iSCSI LIFs per node in ONTAP 9...
Question 18: You just finished an AFF A300 installation with two DS224C d...
Question 19: You are adding two new nodes into an existing switchless 2-n...
Question 20: An administrator is installing a new AFF A220 HA pair and ne...
Question 21: You install a new 2-node FAS8200 switchless cluster. You wan...
Question 22: A customer wants to reduce the disk allocation requirement f...
Question 23: When completing a new ONTAP 9.5 cluster base installation, w...
Question 24: You have just installed a new FAS2620 on a cluster site. You...
Question 25: An iSCSI LIF fails to migrate during a storage failover test...
Question 26: You complete a hardware installation on a CN1610 switch and ...
Question 27: You are going to add a node to an existing cluster but first...
Question 28: Node 3 has taken over Node 4. You are attempting to access N...
Question 29: You are asked to install a new ONTAP cluster at a customer s...
Question 30: While preparing for a new ONTAP installation, you discover a...
Question 31: What is a valid failover policy for a SAN LIF?...
Question 32: A customer has an ONTAP 9.5 8-node FAS8080 EX cluster. The c...
Question 33: You are asked to installed a new cluster with six FAS8060 no...
Question 34: A node joins a cluster in ONTAP 9.5. Which statement is corr...
Question 35: You are setting up a new cluster. The customer notices that ...
Question 36: Which two commands verify that AutoSupport is working as exp...
Question 37: Recently, your 2-node FAS8020 cluster was upgraded from ONTA...
Question 38: You have just replaced a FAS controller with a new controlle...
Question 39: Config Advisor reports that you have a single point of failu...
Question 40: After setting up a new cluster, you run an AutoSupport messa...
Question 41: Which statement about LIFs is true?...
Question 42: Which statement describes an SVM?...
Question 43: In which scenario must ACP be out-of-band?...
Question 44: Which type of partitioning would you use when installing a F...
Question 45: A customer wants to reduce the task allocation requirement f...
Question 46: To ensure that your customer's cluster is robust and operati...
Question 47: A customer ordered two new DS224C shelves. The customer want...
Question 48: You have to disable a switch that is connected to a port on ...
Question 49: You are installing a pair of Cisco Nexus 3132Q-V cluster swi...
Question 50: You are cabling two Cisco 3232C switches for the cluster int...
Question 51: A customer has a stack of shelves with both DS4243 shelves a...
Question 52: A customer has an AFF A800 with 24 internal drives and is ru...
Question 53: In a 4-node cluster, what is function of the HA interconnect...
Question 54: A customer wants you to add a new AFF A700 HA pair to an exi...
Question 55: Referring to the exhibit, which statement describes the dust...
Question 56: (Exhibit) After completing the installation of a DS224C shel...
Question 57: Which two default broadcast domains does the system create d...
Question 58: (Exhibit) You install a new FAS2650 HA with a DS224C disk sh...
Question 59: What are three LIF roles? (choose three.)...
Question 60: You are planning the deployment of a new 8-node ONTAP 9.5 cl...
Question 61: Which NetApp tool relies on PowerShell to produce a comprehe...
Question 62: You finished an ONTAP 9.5 installation using the information...
Question 63: You install a new AFF A300 2-node switchless cluster with ON...
Question 64: Upon finishing the installation of a new system for a custom...
Question 65: You just installed a new AFF A220 2-node cluster without add...
Question 66: You are preparing for a new installation. While determining ...