Prev Next Question 37/66 - NS0-182.v2020-02-08

Recently, your 2-node FAS8020 cluster was upgraded from ONTAP 8.3 to ONTAP 9.5. You have just added two FAS8060 nodes to the cluster. You have executed Config Advisor to verify your work. Config Advisor tells you that the cluster ports on the original two FAS8020 nodes have Flow Control set to FULL.
In this scenario, to what should the Flow Control setting on the FAS8020 ports be set?

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Question List (66q)
Question 1: Which two statements are true about the ONTAP 9.5 networking...
Question 2: What is the maximum number of data disks that a RAID-TEC RAI...
Question 3: (Exhibit) You just installed two nodes into an existing ONTA...
Question 4: Select the Exhibit tab. (Exhibit) You install a new FAS2552 ...
Question 5: You just finish the installation of a single-node cluster. Y...
Question 6: Your customer has a new FAS2650 HA cluster with ONTAP 9.5 in...
Question 7: Select the Exhibit tab. (Exhibit) You install a new FAS2650 ...
Question 8: You must cable a new AFF A700 with two DS224C shelves that a...
Question 9: Which hot-swappable transceiver is required to obtain full p...
Question 10: You need to verify the configuration currently loaded on a C...
Question 11: You have just completed the installation of a FAS9000 HA pai...
Question 12: Your customer has filled out the customer installation works...
Question 13: Click the Exhibit button. (Exhibit) After running Config Adv...
Question 14: You want to grow your current ONTAP cluster. You have a Cisc...
Question 15: You create a LIF called svm_cifs_lif01 on a port that is alr...
Question 16: A customer wants you to add a new AFF A700 HA pair to an exi...
Question 17: What is the minimum number of iSCSI LIFs per node in ONTAP 9...
Question 18: You just finished an AFF A300 installation with two DS224C d...
Question 19: You are adding two new nodes into an existing switchless 2-n...
Question 20: An administrator is installing a new AFF A220 HA pair and ne...
Question 21: You install a new 2-node FAS8200 switchless cluster. You wan...
Question 22: A customer wants to reduce the disk allocation requirement f...
Question 23: When completing a new ONTAP 9.5 cluster base installation, w...
Question 24: You have just installed a new FAS2620 on a cluster site. You...
Question 25: An iSCSI LIF fails to migrate during a storage failover test...
Question 26: You complete a hardware installation on a CN1610 switch and ...
Question 27: You are going to add a node to an existing cluster but first...
Question 28: Node 3 has taken over Node 4. You are attempting to access N...
Question 29: You are asked to install a new ONTAP cluster at a customer s...
Question 30: While preparing for a new ONTAP installation, you discover a...
Question 31: What is a valid failover policy for a SAN LIF?...
Question 32: A customer has an ONTAP 9.5 8-node FAS8080 EX cluster. The c...
Question 33: You are asked to installed a new cluster with six FAS8060 no...
Question 34: A node joins a cluster in ONTAP 9.5. Which statement is corr...
Question 35: You are setting up a new cluster. The customer notices that ...
Question 36: Which two commands verify that AutoSupport is working as exp...
Question 37: Recently, your 2-node FAS8020 cluster was upgraded from ONTA...
Question 38: You have just replaced a FAS controller with a new controlle...
Question 39: Config Advisor reports that you have a single point of failu...
Question 40: After setting up a new cluster, you run an AutoSupport messa...
Question 41: Which statement about LIFs is true?...
Question 42: Which statement describes an SVM?...
Question 43: In which scenario must ACP be out-of-band?...
Question 44: Which type of partitioning would you use when installing a F...
Question 45: A customer wants to reduce the task allocation requirement f...
Question 46: To ensure that your customer's cluster is robust and operati...
Question 47: A customer ordered two new DS224C shelves. The customer want...
Question 48: You have to disable a switch that is connected to a port on ...
Question 49: You are installing a pair of Cisco Nexus 3132Q-V cluster swi...
Question 50: You are cabling two Cisco 3232C switches for the cluster int...
Question 51: A customer has a stack of shelves with both DS4243 shelves a...
Question 52: A customer has an AFF A800 with 24 internal drives and is ru...
Question 53: In a 4-node cluster, what is function of the HA interconnect...
Question 54: A customer wants you to add a new AFF A700 HA pair to an exi...
Question 55: Referring to the exhibit, which statement describes the dust...
Question 56: (Exhibit) After completing the installation of a DS224C shel...
Question 57: Which two default broadcast domains does the system create d...
Question 58: (Exhibit) You install a new FAS2650 HA with a DS224C disk sh...
Question 59: What are three LIF roles? (choose three.)...
Question 60: You are planning the deployment of a new 8-node ONTAP 9.5 cl...
Question 61: Which NetApp tool relies on PowerShell to produce a comprehe...
Question 62: You finished an ONTAP 9.5 installation using the information...
Question 63: You install a new AFF A300 2-node switchless cluster with ON...
Question 64: Upon finishing the installation of a new system for a custom...
Question 65: You just installed a new AFF A220 2-node cluster without add...
Question 66: You are preparing for a new installation. While determining ...