Cisco.300-115.v2019-08-10.q501

Exam Code:300-115
Exam Name:Implementing Cisco IP Switched Networks
Certification Provider:Cisco
Free Question Number:501
Version:v2019-08-10
Rating:
# of views:800
# of Questions views:60664
Start Practice Test

Valid 300-115 Dumps shared by Fast2test.com for Helping Passing 300-115 Exam! Fast2test.com now offer the newest 300-115 exam dumps, the Fast2test.com 300-115 exam questions have been updated and answers have been corrected get the newest Fast2test.com 300-115 dumps with Test Engine here:

Access 300-115 Dumps Premium Version
(162 Q&As Dumps, 40%OFF Special Discount: freecram)

Recent Comments (The most recent comments are at the top.)

furry-fanatic   - Dec 10, 2019

No.# This could be a trick question. They are asking for the "vlan database" which has been deprecated for a very long time. But if this is actually what they mean, then A and D are correct.

But it makes little sense to ask a vlan database question. I don't think it's even in the curriculum anymore. Other than "it's no longer used."

CCNP-Study   - Sep 13, 2019

No.# A and C are correct. Both show vlan, and show vlan brief show all known vlans on a swtich.

Show vlan database does not exist

speedy   - Aug 19, 2019

No.# I think show vlan brief and show vlan correct

show vlan brief

VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi1/0/1, Gi1/0/2, Gi1/0/3
Gi1/0/4, Gi1/0/5, Gi1/0/6
Gi1/0/7, Gi1/0/8, Gi1/0/9
Gi1/0/10, Gi1/0/11, Gi1/0/12
Gi1/0/13, Gi1/0/14, Gi1/0/15
Gi1/0/16, Gi1/0/17, Gi1/0/18
Gi1/0/19, Gi1/0/20, Gi1/0/21
Gi1/0/22, Gi1/0/23, Gi1/0/24
Gi1/0/25, Gi1/0/26, Gi1/0/27
Gi1/0/28, Gi1/0/29, Gi1/0/30
Gi1/0/31, Gi1/0/32, Gi1/0/33
Gi1/0/34, Gi1/0/35, Gi1/0/36
Gi1/0/37, Gi1/0/38, Gi1/0/39

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Other Version
597 viewsCisco.300-115.v2020-01-02.q86
694 viewsCisco.300-115.v2019-10-24.q85
517 viewsCisco.300-115.v2019-09-20.q120
886 viewsCisco.300-115.v2019-06-25.q495
933 viewsCisco.300-115.v2019-02-18.q482
718 viewsCisco.300-115.v2019-01-25.q446
1047 viewsCisco.300-115.v2018-11-27.q443
1027 viewsCisco.300-115.v2018-09-19.q350
1107 viewsCisco.300-115.v2018-08-15.q300
690 viewsCisco.300-115.v2018-06-13.q153
531 viewsCisco.300-115.v2018-06-11.q159
558 viewsCisco.300-115.v2018-06-05.q182
827 viewsCisco.300-115.v2018-05-08.q250
1854 viewsCisco.300-115.v2018-03-23.q215
823 viewsCisco.300-115.v2018-03-19.q200
479 viewsCisco.300-115.v2018-03-09.q151
532 viewsCisco.300-115.v2018-03-04.q139
926 viewsCisco.300-115.v2018-03-02.q185
855 viewsCisco.300-115.v2018-01-21.q285
Exam Question List
Question 1: Which feature can you enable on your network to most effecti...
Question 2: Refer to the exhibit. (Exhibit) Which router is elected as t...
Question 3: A company has the following network infrastructure. (Refer t...
Question 4: Which statement describes the result of issuing the spanning...
Question 5: Refer to the exhibit. Which two actions recover the UDLD err...
Question 6: A network engineer is trying to deploy a PC on a network. Th...
Question 7: At which OSI layer does STP operate?...
Question 8: Instructions Enter IOS commands on the device to verify netw...
Question 9: Refer to the exhibit. (Exhibit) Which option describes the r...
Question 10: (Exhibit) Refer to the exhibit. Which two statements about t...
Question 11: When executed on a HSRP group member named Router 10, what e...
Question 12: What Cisco switch feature allows IP phones to be automatical...
Question 13: Inter-VLAN routing has been operating successfully for sever...
Question 14: What command disables 802.1x authentication on a port and pe...
Question 15: Refer to the output below. Which two effect of this configur...
3 commentQuestion 16: Which two commands display the VLANs that are present in the...
Question 17: Which type of MAC address can be dropped by a switch that is...
Question 18: Which command enables you to determine whether any interface...
Question 19: Which command produced the following output? (Exhibit)...
Question 20: If a network engineer applies the command mac-address-table ...
Question 21: Which two prerequisites for HSRP to become active on an inte...
Question 22: What happens if we add "line" on AAA command?...
Question 23: Refer to the exhibit. (Exhibit) The users in an engineering ...
Question 24: Which two statements about VRRP are true? (Choose two.)...
Question 25: The output displayed below is a result of what command? Inte...
Question 26: Which feature places a port in an err-disabled state when it...
Question 27: What will be behavior of an access port when a tagged packet...
Question 28: Which statement is true about Stackwise?...
Question 29: You have recently deployed an access switch with two fiber c...
Question 30: Which command do you enter to enable Dynamic ARP Inspection ...
Question 31: Refer to the exhibit. Which description of the effect of ent...
Question 32: Which two statements about the local user database are true?...
Question 33: You have configured switches A and B in a network. The gigab...
Question 34: Which feature is automatically enabled when a voice VLAN is ...
Question 35: Which two commands or command sequences configure a switch s...
Question 36: Which two statements about dynamic MAC address learning are ...
Question 37: In the hardware address 0000.0c07.ac0a, what does 07.ac repr...
Question 38: After UDLD is implemented, a Network Administrator noticed t...
Question 39: Which security feature inspects ARP packets based on valid I...
Question 40: What Cisco Catalyst switch feature can be used to define por...
Question 41: Which command prevents all access ports on a switch from sen...
Question 42: Which two configurations can you apply to a port so that it ...
Question 43: The following commands have been issued on a Catalyst switch...
Question 44: Which four LACP components are used to determine which hot-s...
Question 45: In which two circumstances does a port security violation oc...
Question 46: Which IOS command configures a switch for VTP client mode?...
Question 47: Which devices are required to provide connectivity between V...
Question 48: Which two commands enable you to determine the native VLAN t...
Question 49: Which of these two options are true about RADIUS? (Choose tw...
Question 50: Which routers comprise a VRRP group?...
Question 51: Which two statements about UDLD aggressive mode are true? (C...
Question 52: If you have a new switch (that runs spanning-tree mode pvst+...
Question 53: Which two statements are true about StackWise? (Choose two.)...
Question 54: Which two statements about MAC address learning are true? (C...
Question 55: Interface FastEthernet0/1 is configured as a trunk interface...
Question 56: Which two of the following organizationally specific LLDP TL...
Question 57: How many active virtual gateways can each GLBP group support...
Question 58: Which of the following is true about CDP?...
Question 59: Which command enables HSRP on an interface?...
Question 60: What are the three RSTP port states? (Choose three.)...
Question 61: Refer to the exhibit. What is the effect of the given config...
Question 62: Which three features can be optimized by using SDM templates...
Question 63: Which two tasks must you perform to enable AAA operations wi...
Question 64: Which two actions can be configured for storm control violat...
Question 65: Which feature can protect a Layer 2 port from spoofed IP add...
Question 66: Which virtual router states are defined in the GLBP protocol...
Question 67: Which statements about RSPAN are true? (Choose two.)...
Question 68: Which two secondary VLAN types of Private VLANs (PVLANs)? (C...
Question 69: Which two statements about RSPAN VLAN are true? (Choose two....
Question 70: After reviewing UDLD status on switch ports, an engineer not...
Question 71: In which UDLD mode does a link remain up, even when a unidir...
Question 72: Under which two conditions does Cisco StackWise Virtual tran...
Question 73: Pilot testing of the new switching infrastructure finds that...
Question 74: Which two statements about HSRP are true? (Choose two.)...
Question 75: Which benefit of Stackwise is true?...
Question 76: Which two commands sequences must you enter on a pair switch...
Question 77: Which errdisable recovery command option enables a device to...
Question 78: A network engineer wants to ensure Layer 2 isolation of cust...
Question 79: When using EtherChannel misconfiguration guard, which techno...
Question 80: Which command would a network engineer apply to error-disabl...
Question 81: Which two statements about SDM templates are true? (Choose t...
Question 82: Which three methods can be used to manage Cisco APs that are...
Question 83: Which three authentication methods does GLBP use? (Choose th...
Question 84: Which two statements about extended-range VLANs are true? (C...
Question 85: What is the benefit of UDLD?
Question 86: Which statement about the default behavior of a Cisco switch...
Question 87: Which two statements about IP Source Guard are true? (Choose...
Question 88: Which layer private VLAN partition the broadcast domain?...
Question 89: When a private VLAN is configured, which mode must be config...
Question 90: You have executed the following commands on switchA: (Exhibi...
Question 91: What protocol allows for centralized management of multiple ...
Question 92: Consider the following output from the show interfaces trunk...
Question 93: A new switch that contains a configuration consisting of onl...
Question 94: How is load balancing achieved when implementing HSRP?...
Question 95: Which Cisco switch feature enables IP phones to be assigned ...
Question 96: Refer to the exhibit. Which two statements about the network...
Question 97: Which command do you enter so that the default authenticatio...
Question 98: Which information does CDP supply from connected devices? (C...
Question 99: If a switch that is configured globally with DHCP snooping r...
Question 100: In a Cisco StackWise Virtual environment, which planes on th...
Question 101: Which two commands prune VLAN 10 from a switch interface? (C...
Question 102: Which Cisco StackWise feature is supported?...
Question 103: In which VTP modes can you propagate VTP advertisements and ...
Question 104: Which three statements are correct with regard to the IEEE 8...
Question 105: 802.1Q trunking, what does it do? (Choose two.)...
Question 106: Which of the following commands configures a port with a VLA...
Question 107: Which AAA authorization method uses a vendor-neutral directo...
Question 108: On which layer does IP source guard provide filtering to pre...
Question 109: Assuming that preempt is not configured, when does a router ...
Question 110: Which two tasks must you perform to correctly configure IP S...
Question 111: Which tool can error-disable an interface if the storm contr...
Question 112: The network manager has requested that several new VLANs (VL...
Question 113: Which command enables you to determine the spanning-tree gua...
Question 114: Refer to the exhibit. Which two statements about the network...
Question 115: Which private VLAN can have only one VLAN and be a secondary...
Question 116: Which authentication service is needed to configure 802.1x?...
Question 117: Which Cisco component can be enabled on a switch port connec...
Question 118: What is the storm control violation defined by default on a ...
Question 119: What types of SDM templates you can use in switch? (Choose a...
Question 120: Refer to the exhibit. (Exhibit) The network switches for two...
Question 121: Which three statements about extended VLANs are true? (Choos...
Question 122: Which keyword can be applied to the spanning-tree priority c...
Question 123: Which statement about EtherChannels are true?...
Question 124: What statements about STP path cost are true? (Choose two.)...
Question 125: Refer to the exhibit. (Exhibit) An engineer is configuring a...
Question 126: Which two features can you configure on an access port? (Cho...
Question 127: Refer to the exhibit. (Exhibit) Which statement about the SP...
Question 128: What do subordinate switches in a switch stack keep?...
Question 129: Which of the following commands can be issued without interf...
Question 130: Which two commands display trunking information on one or mo...
Question 131: Which command correctly configures standby tracking for grou...
Question 132: Which two statements about recovering error-disabled interfa...
Question 133: In the following partial output of the show run command, whi...
Question 134: Which VTP mode and version should be configured on a switch ...
Question 135: With RSTP hello timers set to the default interval, how quic...
Question 136: Which two statements about sticky MAC address learning are t...
Question 137: When provisioning bandwidth for an IP telephony network, whi...
Question 138: Which two TLVs are included in Cisco Discovery Protocol adve...
Question 139: (Exhibit) Refer to the exhibit. Which two statements about t...
Question 140: Which two statements about Cisco StackWise are true? (Choose...
Question 141: A network engineer configured a fault-tolerance link on Giga...
Question 142: Refer to the output below. Which effect of this configuratio...
Question 143: You made changes to a VLAN, but the changes were not propaga...
Question 144: If all switches in a network have the same spanning-tree pri...
Question 145: Which of the following will cause a switch port to go into t...
Question 146: Which two tasks must you perform on a device to ensure that ...
Question 147: Which two prerequisites are required for an HSRP interface t...
Question 148: What is the default amount by which the hot standby priority...
Question 149: What is the easiest way to force a specific switch to become...
Question 150: Which statement about RSPAN session is true?...
Question 151: Which three functions does Dynamic ARP Inspection perform wi...
Question 152: Which option lists the information that is contained in a Ci...
Question 153: What occurs when an untagged frame is received by an 802.1Q ...
Question 154: Which two VLAN ranges can you add, modify or delete on a swi...
Question 155: An access switch has been configured with an EtherChannel po...
Question 156: Which STP feature used to monitor BPDU traffic and enable ST...
Question 157: Refer to the exhibit. (Exhibit) An engineer is configuring E...
Question 158: Which results happens when a non-trunking port that is confi...
Question 159: Which AAA Authorization type includes PPP, SLIP, and ARAP co...
Question 160: A switch is added into the production network to increase po...
Question 161: Which two statements about 802.1q are true? (Choose two.)...
Question 162: Refer to the exhibit. Which two statements can be derived fr...
Question 163: Which two restrictions of the port security feature are true...
Question 164: ABC, Inc. is a medium sized company, with an enterprise netw...
Question 165: The partial output displayed in the exhibit is a result of w...
Question 166: What is the default port security violation?...
Question 167: Which private VLAN access port belongs to the primary VLAN a...
Question 168: How will a switch become a stack master during election?...
Question 169: When you configure private VLANs on a switch, which port typ...
Question 170: You administer a network that uses two routers, R1 and R2, c...
Question 171: While troubleshooting a network outage, a network engineer d...
Question 172: Which statement about restrictions for multichassis LACP is ...
Question 173: Refer to the exhibit. (Exhibit) Which login credentials are ...
Question 174: Refer to the output below. interface FastEthernet0/1 descrip...
Question 175: An EtherChannel bundle has been established between a Cisco ...
Question 176: A network engineer changed the port speed and duplex setting...
Question 177: A network engineer is considering implementing UDLD througho...
Question 178: An enterprise network has port security sticky enabled on al...
Question 179: What are three possible router states of HSRP routers on a L...
Question 180: Which command sets the interval at which a device sends LLDP...
Question 181: Why the network administration can want to disable MAC addre...
Question 182: What is required for a LAN switch to support 802.1q Q-in-Q e...
Question 183: HSRP has been configured between two Company devices. Which ...
Question 184: Which switchport feature will block the packet with unknown ...
Question 185: If VLAN 99 is set to trunk, how can you set it to untagged f...
Question 186: Which command enables a RADIUS server configuration to use v...
Question 187: You are the network administrator in your company. You have ...
Question 188: Which of the following capabilities does a multilayer switch...
Question 189: Which two types of threshold can you configure for tracking ...
Question 190: Which feature describes MAC addresses that are dynamically l...
Question 191: Refer to the exhibit. (Exhibit) Which statement about switch...
Question 192: Refer to the exhibit. (Exhibit) Users of PC-1 experience slo...
Question 193: Which two tasks can be accomplished to configure multiple HS...
Question 194: When a Layer 2 EtherChannel is configured, which statement a...
Question 195: Which two statements about GLBP are true? (Choose two.)...
Question 196: Refer to the exhibit. (Exhibit) Which configuration ensures ...
Question 197: Refer to the exhibit. (Exhibit) Which configuration ensures ...
Question 198: Which IOS command configures the switch for the VTP mode tha...
Question 199: Which type of network attack takes advantage of the Dynamic ...
Question 200: Which statement is true about RSTP topology changes?...
Question 201: Refer to the exhibit. An engineer is configuring an ethercha...
Question 202: Refer to the exhibit. You have applied these configurations ...
Question 203: Which VLAN range is eligible to be pruned when a network eng...
Question 204: Which three statements about SPAN and RSPAN are true? (Choos...
Question 205: What attack technique attempts to fill a switching table so ...
Question 206: On which PVLAN type can host ports communicate with promiscu...
Question 207: What is the default value for the errdisable recovery interv...
Question 208: How does SPAN interact with STP?...
Question 209: (Exhibit) - DSW1 (Distribution Switch 1) is the primary devi...
Question 210: Which SDM template disables routing and supports the maximum...
Question 211: A switch has a pair of fiber and it has been damaged. Which ...
Question 212: During the implementation of a voice solution, which two req...
Question 213: Which two options are benefits of using VSS for chassis virt...
Question 214: Which option is a CISCO recommended RSPAN configuration prac...
Question 215: Refer to the exhibit. (Exhibit) Which option shows the expec...
Question 216: If G1/0/1 on DSW1 is shutdown, what will be the current prio...
Question 217: Refer to the exhibit. (Exhibit) Switch A, B, and C are trunk...
Question 218: Which feature rate-limits DHCP traffic?...
Question 219: What is the command for configuring root guard?...
Question 220: Which two statements about Cisco Discovery Protocol are true...
Question 221: How long does it take for a port to transition from the STP ...
Question 222: Which two differences between RADIUS and TACACS+ are true? (...
Question 223: Which two functions of DHCP snooping are true? (Choose two.)...
Question 224: Which protocol provides port-based access control and authen...
Question 225: Which option is the value of the Tag Protocol Identifier 802...
Question 226: Which Statement about the default SWITCH Database Management...
Question 227: Which IOS command enables the VTP feature that eliminates un...
Question 228: Which one is related to Stackwise technology?...
Question 229: After the implementation of several different types of switc...
Question 230: Which statement about the connection of two switches with se...
Question 231: For client server failover purposes, the application server ...
Question 232: Refer to the exhibit. Which statement about the interface is...
Question 233: Which two statements about PortFast are true? (Choose two.)...
Question 234: Which command do you enter to troubleshoot a misconfigured E...
Question 235: Refer to the exhibit. (Exhibit) All ports are members of VLA...
Question 236: Which statement is true when UDLD is configured on a link an...
Question 237: A network engineer is extending a LAN segment between two ge...
Question 238: Which two device types does DHCP snooping treat as untrusted...
Question 239: What effect does the mac address-table aging-time 180 comman...
Question 240: Which technique allows specific VLANs to be strictly permitt...
Question 241: Which two statements about the VLAN database are true? (Choo...
Question 242: Refer to the exhibit. (Exhibit) Which effect of this configu...
Question 243: Which form of centralized device authentication allows each ...
Question 244: Which two TLVs are mandatory in LLDP advertisements? (Choose...
Question 245: Which protocol specified by RFC 2281 provides network redund...
Question 246: Which two VLAN ranges can you add, modify, or delete on a sw...
Question 247: If HSRP group number is 37, what would be the vMAC (virtual ...
Question 248: Which describes the default load balancing scheme used by th...
Question 249: Examine the configuration shown below in a partial output of...
Question 250: Which statement about GLBP is true?...
Question 251: Network engineer wants to use UDLD, what he need to consider...
Question 252: Where should the Root Guard be implemented in the network to...
Question 253: Which two commands verify the DHCP snooping configuration on...
Question 254: When the switches in a Cisco StackWise stack elect a new mas...
Question 255: Which two statements about the monitored traffic in a SPAN s...
Question 256: Which two statements about normal-range VLANs are true? (Cho...
Question 257: What happens when a port configured with root-inconsistent r...
Question 258: Which options of VLANs IDs are in extended range? (Choose th...
Question 259: Consider the following output of the show spanning-tree comm...
Question 260: How to configure dynamic ARP inspection on a VLAN?...
Question 261: Where does the VLAN information get saved to?...
Question 262: What percentage of bandwidth is reduced when a stack cable i...
Question 263: Which two statements about the LACP port priority of a devic...
Question 264: Which of the following HSRP router states does an active rou...
Question 265: Which feature prevents an interface from sending BPDUs on a ...
Question 266: Which First Hop Redundancy Protocol is an IEEE Standard?...
Question 267: (Exhibit) Refer the exhibit. Which two statements about the ...
Question 268: Which two statements about errdisable recovery are true? (Ch...
Question 269: Examine the following partial output of the show run command...
Question 270: Which option is a benefit of configuring UDLD on a link betw...
Question 271: Which HSRP feature allows a router to take over as the activ...
Question 272: Refer to the output below. Which effect of this configuratio...
Question 273: Which two circumstances can cause a port to errdisable? (Cho...
Question 274: What can happen after a RSPAN configuration in a Cisco switc...
Question 275: A server with a statically assigned IP address is attached t...
Question 276: ABC, Inc. is a medium sized company, with an enterprise netw...
Question 277: A network engineer is trying to prevent users from connectin...
Question 278: What are two advantages of LLDP over Cisco Discovery Protoco...
Question 279: If switch SW1 is connected in a mesh with four other switche...
Question 280: Refer to the exhibit. (Exhibit) A network engineer changes t...
Question 281: Which command configures an interface to accept LLDP packets...
Question 282: Which AAA authorization type applies security policies on a ...
Question 283: Which two statements about MST are true? (Choose two.)...
Question 284: Refer to the exhibit. Three switches are configured for HSRP...
Question 285: What is the maximum number of virtual MAC addresses that GLB...
Question 286: Refer to the following network diagram: (Exhibit) You execut...
Question 287: When you design a switched network using VTPv2, how many VLA...
Question 288: After port security is deployed throughout an enterprise cam...
Question 289: When you enable MST on the switch, what happens?...
Question 290: Which statement describes what happens when a port configure...
Question 291: In a switch stack environment, what is the total bidirection...
Question 292: Which option is a benefit of using VSS?...
Question 293: Which two new features are included in VTPv3? (Choose two.)...
Question 294: Which statement is true about HSRP?...
Question 295: Which statement describes the result of configuring SPAN on ...
Question 296: Which statement about VLAN pruning on trunk ports is true?...
Question 297: ABC, Inc. is a medium sized company, with an enterprise netw...
Question 298: Refer to the exhibit. (Exhibit) Why would the switch be cons...
Question 299: Which two statements about HSRP timers are true? (Choose two...
Question 300: Which feature is automatically configured when an administra...
Question 301: Your manager asked you to make every port on your switch byp...
Question 302: Which two features are new in VTPv3? (Choose two.)...
Question 303: Which IOS command sets the native VLAN to VLAN3?...
Question 304: A new network that consists of several switches has been con...
Question 305: What is the multicast address for HSRPv2?...
Question 306: Refer to the exhibit. Which two effects of this configuratio...
Question 307: What is the behavior of an access port when a tagged packet ...
Question 308: The command storm-control broadcast level 75 65 is configure...
Question 309: Which configuration do you apply to an interface so that it ...
Question 310: Which load-balancing algorithm does GLBP use by default?...
Question 311: What are possible Etherchannel load balancing mechanism base...
Question 312: Which information is true about RSPAN?...
Question 313: Which Catalyst 6500 feature provides network-security enforc...
Question 314: A network engineer must implement Ethernet links that are ca...
Question 315: Which two commands add VLAN 20 to the VLAN configuration fil...
Question 316: Which statement about the VTPv2 is true?...
Question 317: Interfaces are assigned to a VLAN, and then the VLAN is dele...
Question 318: After configuring new data VLANs 1020 through 1030 on the VT...
Question 319: Given the configuration on a switch interface, what happens ...
Question 320: Which action allows a network engineer to limit a default VL...
Question 321: Which characteristics apply to multilayer switching? (Choose...
Question 322: Which two statements about CDP are true? (Choose two.)...
Question 323: Which next-hop router redundancy protocol provides backup fo...
Question 324: Which of the following statements best describes the result ...
Question 325: Refer to the exhibit. (Exhibit) A multilayer switch has been...
Question 326: What is the value of the TPID/tag protocol identifier of Qin...
Question 327: What is the Ethernet frame size for 802.1Q?...
Question 328: Which technique will control broadcast, multicast and unicas...
Question 329: What happens if you apply this command "vlan dot1q tag nativ...
Question 330: A network engineer configured an Ethernet switch using these...
Question 331: Which configuration do you apply to an interface so that a h...
Question 332: (Exhibit) A network engineer deployed an older switch with t...
Question 333: Refer to the exhibit. (Exhibit) f1/0 and f1/1 have the same ...
Question 334: Refer to the exhibit. You have configured routers R1 and R2 ...
Question 335: If EtherChannel guard is configured, how the interface statu...
Question 336: Which virtual MAC address does HSRP group 37 use with defaul...
Question 337: Refer to exhibit, which two statements correctly indicate wh...
Question 338: Which statement about the UDLD protocol is true?...
Question 339: In which two ways are IEEE STP BPDUs forwarded if VLAN 99 is...
Question 340: Which command sequence do you enter to configure an RSPAN VL...
Question 341: What happens if a switch with dhcp snooping and ip source gu...
Question 342: Which statement about frame SPAN is true?...
Question 343: Which two ways can you use to disable Cisco Discovery Protoc...
Question 344: Which statement about using EtherChannel on Cisco IOS switch...
Question 345: What IOS VLAN commands would create a new VLAN and assign it...
Question 346: Which three pieces of information about the remote device ar...
Question 347: A Cisco Catalyst switch that is prone to reboots continues t...
Question 348: What is needed for Virtual Switching System "VSS"?...
Question 349: Which hot standby groups numbers are used in a HSRP token ri...
Question 350: Which of the following statements are TRUE about the selecti...
Question 351: What VSS technology allows you to share downstream resources...
Question 352: What will extend a trust boundary (There is a switch interfa...
Question 353: Which of the following are true regarding TACACS+. ? (Choose...
Question 354: Refer to the exhibit. Which path does PC1 take to reach DSW1...
Question 355: What is the default violation status of port security?...
Question 356: Which switch is chosen as the stack master during a stack ma...
Question 357: How does the Spanning Tree Protocol determine path cost?...
Question 358: Refer to the following partial output of the show spanning-t...
Question 359: What command would display a single line of information for ...
Question 360: Which two statements about an access port with voice VLAN ar...
Question 361: Which command configures VLAN 99 as an untagged VLAN on a tr...
Question 362: Which statement describes what happens if all VSL connection...
Question 363: VLAN maps have been configured on switch R1. Which of the fo...
Question 364: What are the prerequisite for HSRP interface to come up? (Ch...
Question 365: Which redundancy mode for supervisor engine modules exhibits...
Question 366: Which two possible EtherChannel load balancing mechanisms ar...
Question 367: What statement is true about PVST?...
Question 368: Which of the following are true regarding TACACS+ ? (Choose ...
Question 369: A Cisco switch was configured using the "switchport trunk al...
Question 370: (Exhibit) Refer to the exhibit. An engineer entered the no s...
Question 371: Which two ISP devices should have trust Port-Statement with ...
Question 372: Which IOS command do you use to remove Layer 2 configuration...
Question 373: Which will identify the master switch in stackwise?...
Question 374: What is the maximum number of 10 Gigabit Ethernet connection...
Question 375: EtherChannel guard misconfig is configured on a switch, whic...
Question 376: What is the process to configure EtherChannel?...
Question 377: You want to configure your Catalyst 6500 switch to redirect ...
Question 378: What command produced the output in the exhibit? (Exhibit)...
Question 379: What two things occur when an RSTP edge port receives a BPDU...
Question 380: ABC, Inc. is a medium sized company, with an enterprise netw...
Question 381: Which two mandatory TLV types does LLDP advertise? (Choose t...
Question 382: Which statement about the MAC address sticky entries in the ...
Question 383: Refer to the exhibit. Which two statements can be derived fr...
Question 384: Refer to the exhibit. (Exhibit) DSW1 should share the same M...
Question 385: When port security is configured on a switch, which violatio...
Question 386: Consider the following commands executed on a Layer 3 switch...
Question 387: You have three switches connected as shown in the diagram be...
Question 388: Which command can be used to block a frame with an unknown d...
Question 389: Which two statements about GLBP are true? (Choose two.)...
Question 390: For which reason does an administrator disable MAC address l...
Question 391: Which command globally enables AAA on a device?...
Question 392: Which two operational attributes can be checked for EtherCha...
Question 393: Which device type can act as a client in a system that uses ...
Question 394: What happens if an interface within channel group is configu...
Question 395: What are the possible results of port-security?...
Question 396: Which command disables spanning tree on multiple ports?...
Question 397: What does the command vlan dot1q tag native accomplish when ...
Question 398: What is true about CDP? (Choose two.)...
Question 399: Which two commands configure RSPAN to capture incoming and o...
Question 400: Which gateway role is responsible for answering ARP requests...
Question 401: Which statement is true when one of its virtual gateway redu...
Question 402: Which option is the maximum frame size for an 802.1Q frame?...
Question 403: You have added a new switch to a Cisco StackWise stack. If t...
Question 404: Refer to the exhibit. Switch 15 is configured as the root sw...
Question 405: You move a switch from a network where it performed Layer 2 ...
Question 406: An administrator recently configured all ports for rapid tra...
Question 407: When a Cisco Catalyst switch that is configured in VTP serve...
Question 408: Which statement about Layer 2 protocol participation of port...
Question 409: Refer to the exhibit. (Exhibit) A network engineer wants to ...
Question 410: An access switch at a remote location is connected to the sp...
Question 411: Which will identify the master switch in stack wise?...
Question 412: Which information in a RADIUS access-request packet is encry...
Question 413: If HSRP group number is 45 what would be the MAC address? (B...
Question 414: Which two statements about VRRP advertisements are true? (Ch...
Question 415: Which two commands configure SPAN to monitor outgoing traffi...
Question 416: Which feature actively validates DHCP messages and drops inv...
Question 417: What is the first step STP performs to establish a loop-free...
Question 418: A network engineer wants to make sure that an access switch ...
Question 419: A switch which was connected with 2 fiber cables attached to...
Question 420: Which two tasks must you perform to enable DHCP option 82 on...
Question 421: Refer to the exhibit. Based upon the output of show vlan on ...
Question 422: A network engineer has just deployed a non-Cisco device in t...
Question 423: In regards to Cisco Virtual Switching System which technolog...
Question 424: As the network administrator, you have enabled port security...
Question 425: Refer to the exhibit. Based on the debug output, which three...
Question 426: Refer to the exhibit. What is the result of setting GLBP wei...
Question 427: What is the link called between a VSS?...
Question 428: You have configured three routers in HSRP group 10 to provid...
Question 429: Instructions: Enter IOS commands on the device to verify net...
Question 430: Which database is used to determine the validity of an ARP p...
Question 431: Which command is used to verify trunk native VLANs?...
Question 432: A network engineer must adjust the STP interface attributes ...
Question 433: The following command was issued on a router that is being c...
Question 434: Which two methods are used to configure a trusted option 82?...
Question 435: Which IOS commands should you enter in interface configurati...
Question 436: Which fallback method can you configure to allow all AAA aut...
Question 437: If all devices on an EtherChannel are sending traffic to a s...
Question 438: Which two statements about VRRP object tracking are true? (C...
Question 439: Enablement of which feature puts the port into err-disabled ...
Question 440: Which extended VLAN range are valid and is stored in the sta...
Question 441: Refer to the following partial output of the debug standby c...
Question 442: You want to create a VTP domain named myvtpdomain and define...
Question 443: The network monitoring application alerts a network engineer...
Question 444: Which statement about SPAN is true?...
Question 445: Which command enables PortFast and disables port channel on ...
Question 446: What command configures a port with a voice VLAN using 802.1...
Question 447: What is accomplished by the command switchport port-security...
Question 448: Which two statements about GLBP are true? (Choose two.)...
Question 449: Which feature do you implement so that a physical port will ...
Question 450: Several new switches have been added to the existing network...
Question 451: Which IOS commands are entered in interface configuration mo...
Question 452: When you connect an internal switch to an upstream provider ...
Question 453: Based on the show spanning-tree vlan 200 output shown in the...
Question 454: Which portion of AAA looks at what a user has access to?...
Question 455: Which command do you enter on a device so that users are aut...
Question 456: Which two port err-disabled recovery options are used to det...
Question 457: Which two statements about HSRP, GLBP, and VRRP are true? (C...
Question 458: An engineer is configuring an EtherChannel between two switc...
Question 459: Which command can you enter to most effectively rate-limit m...
Question 460: Refer to the exhibit. (Exhibit) If all switches in this envi...
Question 461: Which three HSRP exchange states are used in multicast messa...
Question 462: What attack technique uses double VLAN tagging to access net...
Question 463: Refer to the exhibit. (Exhibit) A single server in Company A...
Question 464: Which command must be configured on the physical ports of a ...
Question 465: Which statement describes what a port that is configured as ...
Question 466: Instructions Enter IOS commands on the device to verify netw...
Question 467: Instructions: Enter IOS commands on the device to verify net...
Question 468: Which of the following is required to allow load balancing b...
Question 469: Which HSRP extension allows groups to share traffic loads?...
Question 470: Which switch feature prevents traffic on a LAN from being ov...
Question 471: Which protocol is used to propagate voice VLANs to a Cisco p...
Question 472: After an EtherChannel is configured between two Cisco switch...
Question 473: A physical switch port is part of an EtherChannel group. Wha...
Question 474: You have executed the following set of commands on a Layer 3...
Question 475: Which three characteristics of AAA with RADIUS are true? (Ch...
Question 476: Which two statements about source port monitoring in SPAN ar...
Question 477: How will the traffic reach the core switch from AS switch to...
Question 478: Refer to the exhibit. Which configuration on the HSRP neighb...
Question 479: What Cisco Catalyst switch feature is designed to inspect AR...
Question 480: Where can you disable MAC address learning on the switch?...
Question 481: Which two commands is used to remove VLAN 55 from the trunk ...
Question 482: Which statement is true about GLBP?...
Question 483: Which two requirements for dot1q trunking in IOS are true? (...
Question 484: Which command configures all access ports on a switch to imm...
Question 485: Which statement about the use of PagP link aggregation on a ...
Question 486: Which configuration command ties the router hot standby prio...
Question 487: Refer to the exhibit. Which statement describes the result i...
Question 488: What is the maximum number of switches that can be stacked u...
Question 489: Which two statements about HSRP is true? (Choose two.)...
Question 490: You want to configure a switched internetwork with multiple ...
Question 491: What happens when a destination SPAN port that is configured...
Question 492: How to configure loop guard in a Cisco switch IOS?...
Question 493: What is the default spanning tree port priority?...
Question 494: In a switch stack where is the SDM template stored?...
Question 495: A DHCP configured router is connected directly to a switch t...
Question 496: Which two advantages of LLDP are used over CDP? (Choose two....
Question 497: Which two statements apply to topology-based switching? (Cho...
Question 498: Which two statements apply to LLDP? (Choose two.)...
Question 499: Which switch feature determines validity based on IP-to-MAC ...
Question 500: Refer to the exhibit. An engineer has run the show EtherChan...
Question 501: Which two configuration requirements for port security are t...