Juniper.JN0-348.v2020-02-25.q40

Exam Code:JN0-348
Exam Name:Enterprise Routing and Switching, Specialist (JNCIS-ENT)
Certification Provider:Juniper
Free Question Number:40
Version:v2020-02-25
Rating:
# of views:176
# of Questions views:1268
Start Practice Test

Valid JN0-348 Dumps shared by PrepAwayExam.com for Helping Passing JN0-348 Exam! PrepAwayExam.com now offer the newest JN0-348 exam dumps, the PrepAwayExam.com JN0-348 exam questions have been updated and answers have been corrected get the newest PrepAwayExam.com JN0-348 dumps with Test Engine here:

Access Premium Version
(95 Q&As Dumps, 40%OFF Special Discount: freecram)

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Other Version
398 viewsJuniper.JN0-348.v2019-10-15.q45
295 viewsJuniper.JN0-348.v2019-10-01.q33
Exam Question List
Question 1: You have an existing Virtual Chassis consisting of five memb...
Question 2: What are two OSPF packet types that use multicast for commun...
Question 3: You are adding a new EX4300 member switch to your existing E...
Question 4: Click the Exhibit button. Referring to the exhibit, which po...
Question 5: You want to configure your Junos device so that routing info...
Question 6: Which two statements are true about the IRB interface? (Choo...
Question 7: Referring to the exhibit, which three statements are true? (...
Question 8: What are two terminating actions of a Layer 2 firewall filte...
Question 9: Which two OSPF header fields must match to form an adjacency...
Question 10: Both the R1 and R2 devices are advertising prefix X into AS ...
Question 11: You disconnected a switch from the Virtual Chassis, but the ...
Question 12: Click the Exhibit button. Switch-1 in the exhibit receives a...
Question 13: You are adding a new EX4300 member switch to your existing E...
Question 14: You configured a GRE tunnel that traverses a path using defa...
Question 15: Your router is configured to peer with your ISP's router usi...
Question 16: Referring to the exhibit, which configuration change is need...
Question 17: Click the Exhibit button. The exhibit shows that Host-1 and ...
Question 18: Which two sequences correctly describe the processing order ...
Question 19: You are troubleshooting your OSPF configuration and notice t...
Question 20: Given the route shown in the exhibit, which two prefixes con...
Question 21: You want to configure Layer 2 services over an IP-based tunn...
Question 22: You are enabling dynamic ARP inspection on an EX4300 switch....
Question 23: Which statement is true when using LAGs with an EX4300?...
Question 24: Click the Exhibit button. A number of reports from end-users...
Question 25: You manage a Layer 2 network that spans two buildings. You a...
Question 26: Which two statements are true about DIS elections in IS-IS? ...
Question 27: Referring to the exhibit, what is the problem? (Exhibit)...
Question 28: Which statement is true about Layer 2 firewall filters on EX...
Question 29: Which three statements are true regarding not-so-stubby area...
Question 30: You have configured OSPF routing as shown in the exhibit. Yo...
Question 31: Referring to the output shown in the exhibit, which statemen...
Question 32: Which three mechanisms are associated with the bridging proc...
Question 33: You have configured the router with an IS-IS interface metri...
Question 34: A routing table contains multiple BGP routes to the same des...
Question 35: Click the Exhibit button. Given the configuration shown in t...
Question 36: Which two port security features use the DHCP snooping datab...
Question 37: What are the three possible port states when using RSTP? (Ch...
Question 38: Which two statements about DHCP snooping are correct? (Choos...
Question 39: What are three extended BGP communities? (Choose three.)...
Question 40: Referring to the exhibit, which statement explains why the r...